mirror
/
openwrt
mirror of https://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Releases Activity

mediatek: add Zyxel EX5601-T0 with uboot custom partition 

The flash procedure is similar to the Xiaomi AX6000 router.

Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:

tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

Format ubi and create ubootenv partitions

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2  openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n  /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb

To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.

Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:

The Power LED was not working correctly and not reacting
 to the boot process and statuses.

The board has space (footprint) for an unpopulated Zigbee chip,
 while we dont know the device model having this chip populated
 we have to assure that the common dts doesnt enable
 interfaces that share pins with such device.

In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
 UART1 seems to be used as a flash port while UART2 should be the
 main comunication interface of Zigbee chip.

The Zigbee chip should be a EFR32MG21. But the pins used for UART
 seems to be not on standard PINS used by other adapters.
 So it cannot run firmwares shared on the web.
 But it should be possible to build a custom firmware with
 the corrtect pinmux.

This commit also contains the following squashed commit from hitech95
 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod

Changes and fixes added in common board:
 - added aliases for boot status leds.
 - added aliases for the mac-label-device.
 - added pin claims for core features (MDIO and UART 0)
 - added default LEDs configuration (01_leds)
 - added default network configuration (02_network)
 - added missing kmod-usb3 module for USB3
 - fixed LED names
 - fixed reset pin for SLIC chip
 - removed unused pinmux configurations and devices
 - fix LAN (switch) port numbering
 - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
 - proper factory partition and mac address handling
 - cleaned up spi_nand sections and partition

Changes and fixxes added in stock layout:
 - added NMBM, if u-boot has it, the kernel must be informed.

Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
(cherry picked from commit b5df398a36)
This commit is contained in:
Valerio 'ftp21' Mancini 2023-10-04 11:43:25 +02:00 committed by Daniel Golle
parent e2954a1e1b
commit 6bec68062b
8 changed files with 666 additions and 524 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

433
target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-common.dtsi Normal file
View File

@ -0,0 +1,433 @@
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
* Copyright (C) 2021 MediaTek Inc.
* Author: Sam.Shih <sam.shih@mediatek.com>
*/
#include "mt7986a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
aliases {
serial0 = &uart0;
label-mac-device = &gmac0;
led-boot = &led_status_green;
led-failsafe = &led_status_red;
led-running = &led_status_green;
led-upgrade = &led_status_red;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0 0x40000000 0 0x40000000>;
};
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "fixed-5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
regulator-always-on;
};
gpio-keys {
compatible = "gpio-keys";
poll-interval = <20>;
reset-button {
label = "reset";
gpios = <&pio 21 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wlan-button {
label = "wlan";
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WLAN>;
};
wps-button {
label = "wps";
gpios = <&pio 56 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led_green_wifi24g {
label = "green:wifi24g";
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_wifi5g {
label = "green:wifi5g";
gpios = <&pio 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_inet {
label = "green:inet";
gpios = <&pio 14 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_red_inet {
label = "red:inet";
gpios = <&pio 15 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_status_green: led_green_pwr {
label = "green:pwr";
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "timer"; /* Default blinking */
led-pattern = <125 125>; /* Fast blink is 4 HZ */
};
led_status_red: led_red_pwr {
label = "red:pwr";
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_fxs {
label = "green:fxs";
gpios = <&pio 16 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_fxs {
label = "amber:fxs";
gpios = <&pio 17 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_wps24g {
label = "amber:wps24g";
gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_wps5g {
label = "amber:wps5g";
gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_green_lan {
label = "green:lan";
gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_green_sfp {
label = "green:sfp";
gpios = <&pio 24 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi_flash_pins>;
cs-gpios = <0>, <0>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
spi_nand: spi_nand@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spi-nand";
reg = <1>;
spi-max-frequency = <10000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
nand_partitions: partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
};
};
};
&eth {
pinctrl-names = "default";
pinctrl-0 = <&eth_pins>;
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "2500base-x";
phy = <&phy6>;
};
mdio: mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
reset-delay-us = <1500000>;
reset-post-delay-us = <1000000>;
phy5: phy@5 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <5>;
mxl,led-config = <0x03f0 0x0 0x0 0x0>;
};
phy6: phy@6 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <6>;
mxl,led-config = <0x00f0 0x0 0x0 0x0>;
};
switch@1f {
compatible = "mediatek,mt7531";
reg = <31>;
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
label = "lan2";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@3 {
reg = <3>;
label = "lan4";
};
port@5 {
reg = <5>;
label = "lan1";
phy-mode = "2500base-x";
phy = <&phy5>;
};
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
};
};
&watchdog {
status = "okay";
};
&wifi {
status = "okay";
pinctrl-names = "default", "dbdc";
pinctrl-0 = <&wf_2g_5g_pins>;
pinctrl-1 = <&wf_dbdc_pins>;
};
&crypto {
status = "okay";
};
&pio {
eth_pins: eth-pins {
mux {
function = "eth";
groups = "switch_int", "mdc_mdio";
};
};
spic_pins_g2: spic-pins-29-to-32 {
mux {
function = "spi";
groups = "spi1_2";
};
};
spi_flash_pins: spi-flash-pins-33-to-38 {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
drive-strength = <8>;
mediatek,pull-up-adv = <0>; /* bias-disable */
};
conf-pd {
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
drive-strength = <8>;
mediatek,pull-down-adv = <0>; /* bias-disable */
};
};
uart0_pins: uart0-pins {
mux {
function = "uart";
groups = "uart0";
};
};
uart1_pins: uart1-pins {
mux {
function = "uart";
groups = "uart1";
};
};
uart2_pins: uart2-pins {
mux {
function = "uart";
groups = "uart2";
};
};
wf_2g_5g_pins: wf_2g_5g-pins {
mux {
function = "wifi";
groups = "wf_2g", "wf_5g";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
};
wf_dbdc_pins: wf_dbdc-pins {
mux {
function = "wifi";
groups = "wf_dbdc";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
};
usb-oc-hog {
gpio-hog;
gpios = <7 GPIO_ACTIVE_LOW>;
input;
line-name = "usb-oc";
};
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spic_pins_g2>;
status = "okay";
proslic_spi: proslic_spi@0 {
compatible = "silabs,proslic_spi";
reg = <0>;
spi-max-frequency = <10000000>;
spi-cpha = <1>;
spi-cpol = <1>;
channel_count = <1>;
debug_level = <4>; /* 1 = TRC, 2 = DBG, 4 = ERR */
reset_gpio = <&pio 25 GPIO_ACTIVE_HIGH>;
ig,enable-spi = <1>; /* 1: Enable, 0: Disable */
};
};
&ssusb {
vusb33-supply = <&reg_3p3v>;
vbus-supply = <&reg_5v>;
status = "okay";
};
&trng {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
/* EFR32MG21 Zigbee (BOOT)*/
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
/* EFR32MG21 Zigbee */
};
&usb_phy {
status = "okay";
};

598
target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-stock.dts
View File

@ -6,6 +6,7 @@
/dts-v1/;
#include "mt7986a.dtsi"
#include "mt7986a-zyxel-ex5601-t0-common.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
@ -13,540 +14,64 @@
model = "Zyxel EX5601-T0";
compatible = "zyxel,ex5601-t0", "mediatek,mt7986a-rfb-snand";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0 0x40000000 0 0x40000000>;
};
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "fixed-5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
regulator-always-on;
};
gpio-keys {
compatible = "gpio-keys";
poll-interval = <20>;
reset-button {
label = "reset";
gpios = <&pio 21 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wlan-button {
label = "wlan";
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WLAN>;
};
wps-button {
label = "wps";
gpios = <&pio 56 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
zyleds {
compatible = "gpio-leds";
led_green_wifi24g {
label = "zyled-green-wifi24g";
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_wifi5g {
label = "zyled-green-wifi5g";
gpios = <&pio 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_inet {
label = "zyled-green-inet";
gpios = <&pio 14 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_red_inet {
label = "zyled-red-inet";
gpios = <&pio 15 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_pwr {
label = "zyled-green-pwr";
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "timer"; /* Default blinking */
led-pattern = <125 125>; /* Fast blink is 4 HZ */
};
led_red_pwr {
label = "zyled-red-pwr";
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led_green_fxs {
label = "zyled-green-fxs";
gpios = <&pio 16 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_fxs {
label = "zyled-amber-fxs";
gpios = <&pio 17 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_wps24g {
label = "zyled-amber-wps24g";
gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_amber_wps5g {
label = "zyled-amber-wps5g";
gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_green_lan {
label = "zyled-green-lan";
gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led_green_sfp {
label = "zyled-green-sfp";
gpios = <&pio 24 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
};
&eth {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
nvmem-cells = <&macaddr_factory_002a>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "2500base-x";
phy = <&phy6>;
nvmem-cells = <&macaddr_factory_0024>;
nvmem-cell-names = "mac-address";
};
mdio: mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
reset-delay-us = <1500000>;
reset-post-delay-us = <1000000>;
phy5: phy@5 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <5>;
};
phy6: phy@6 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <6>;
};
switch@1f {
compatible = "mediatek,mt7531";
reg = <31>;
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
label = "lan1";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan3";
};
port@5 {
reg = <5>;
label = "lan4";
phy-mode = "2500base-x";
phy = <&phy5>;
};
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
};
&watchdog {
status = "okay";
&spi_nand {
mediatek,nmbm;
mediatek,bmt-max-ratio = <1>;
mediatek,bmt-max-reserved-blocks = <64>;
};
&wifi {
status = "okay";
pinctrl-names = "default", "dbdc";
pinctrl-0 = <&wf_2g_5g_pins>;
pinctrl-1 = <&wf_dbdc_pins>;
mediatek,mtd-eeprom = <&factory 0x0>;
nvmem-cells = <&macaddr_factory_0004>;
nvmem-cell-names = "mac-address";
};
&nand_partitions {
&crypto {
status = "okay";
};
&mmc0 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&mmc0_pins_default>;
pinctrl-1 = <&mmc0_pins_uhs>;
bus-width = <8>;
max-frequency = <200000000>;
cap-mmc-highspeed;
mmc-hs200-1_8v;
mmc-hs400-1_8v;
hs400-ds-delay = <0x14014>;
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&reg_1p8v>;
non-removable;
no-sd;
no-sdio;
status = "disabled";
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pcie_pins>;
status = "okay";
};
&pcie_phy {
status = "okay";
};
&pio {
mmc0_pins_default: mmc0-pins {
mux {
function = "emmc";
groups = "emmc_51";
};
conf-cmd-dat {
pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
"EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
"EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
input-enable;
drive-strength = <4>;
mediatek,pull-up-adv = <1>; /* pull-up 10K */
};
conf-clk {
pins = "EMMC_CK";
drive-strength = <6>;
mediatek,pull-down-adv = <2>; /* pull-down 50K */
};
conf-ds {
pins = "EMMC_DSL";
mediatek,pull-down-adv = <2>; /* pull-down 50K */
};
conf-rst {
pins = "EMMC_RSTB";
drive-strength = <4>;
mediatek,pull-up-adv = <1>; /* pull-up 10K */
};
partition@0 {
label = "BL2";
reg = <0x00000 0x0100000>;
read-only;
};
mmc0_pins_uhs: mmc0-uhs-pins {
mux {
function = "emmc";
groups = "emmc_51";
};
conf-cmd-dat {
pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
"EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
"EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
input-enable;
drive-strength = <4>;
mediatek,pull-up-adv = <1>; /* pull-up 10K */
};
conf-clk {
pins = "EMMC_CK";
drive-strength = <6>;
mediatek,pull-down-adv = <2>; /* pull-down 50K */
};
conf-ds {
pins = "EMMC_DSL";
mediatek,pull-down-adv = <2>; /* pull-down 50K */
};
conf-rst {
pins = "EMMC_RSTB";
drive-strength = <4>;
mediatek,pull-up-adv = <1>; /* pull-up 10K */
};
partition@100000 {
label = "u-boot-env";
reg = <0x0100000 0x0080000>;
};
pcie_pins: pcie-pins {
mux {
function = "pcie";
groups = "pcie_clk", "pcie_wake", "pcie_pereset";
};
factory: partition@180000 {
label = "Factory";
reg = <0x180000 0x0200000>;
read-only;
};
spic_pins_g2: spic-pins-29-to-32 {
mux {
function = "spi";
groups = "spi1_2";
};
partition@380000 {
label = "FIP";
reg = <0x380000 0x01C0000>;
read-only;
};
spi_flash_pins: spi-flash-pins-33-to-38 {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
drive-strength = <8>;
mediatek,pull-up-adv = <0>; /* bias-disable */
};
conf-pd {
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
drive-strength = <8>;
mediatek,pull-down-adv = <0>; /* bias-disable */
};
partition@540000 {
label = "zloader";
reg = <0x540000 0x0040000>;
read-only;
};
uart1_pins: uart1-pins {
mux {
function = "uart";
groups = "uart1";
};
partition@580000 {
label = "ubi";
reg = <0x580000 0x4000000>;
};
uart2_pins: uart2-pins {
mux {
function = "uart";
groups = "uart2";
};
partition@4580000 {
label = "ubi2";
reg = <0x4580000 0x4000000>;
read-only;
};
wf_2g_5g_pins: wf_2g_5g-pins {
mux {
function = "wifi";
groups = "wf_2g", "wf_5g";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
partition@8580000 {
label = "zyubi";
reg = <0x8580000 0x15A80000>;
};
wf_dbdc_pins: wf_dbdc-pins {
mux {
function = "wifi";
groups = "wf_dbdc";
};
conf {
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
"WF1_TOP_CLK", "WF1_TOP_DATA";
drive-strength = <4>;
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi_flash_pins>;
cs-gpios = <0>, <0>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
spi_nand: spi_nand@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spi-nand";
reg = <1>;
spi-max-frequency = <10000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "BL2";
reg = <0x00000 0x0100000>;
read-only;
};
partition@100000 {
label = "u-boot-env";
reg = <0x0100000 0x0080000>;
};
factory: partition@180000 {
label = "Factory";
reg = <0x180000 0x0200000>;
read-only;
};
partition@380000 {
label = "FIP";
reg = <0x380000 0x01C0000>;
read-only;
};
partition@540000 {
label = "zloader";
reg = <0x540000 0x0040000>;
read-only;
};
partition@580000 {
label = "ubi";
reg = <0x580000 0x4000000>;
};
partition@4580000 {
label = "ubi2";
reg = <0x4580000 0x4000000>;
read-only;
};
partition@8580000 {
label = "zyubi";
reg = <0x8580000 0x15A80000>;
};
};
};
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spic_pins_g2>;
status = "okay";
proslic_spi: proslic_spi@0 {
compatible = "silabs,proslic_spi";
reg = <0>;
spi-max-frequency = <10000000>;
spi-cpha = <1>;
spi-cpol = <1>;
channel_count = <1>;
debug_level = <4>; /* 1 = TRC, 2 = DBG, 4 = ERR */
reset_gpio = <&pio 7 GPIO_ACTIVE_HIGH>;
ig,enable-spi = <1>; /* 1: Enable, 0: Disable */
};
};
&ssusb {
vusb33-supply = <&reg_3p3v>;
vbus-supply = <&reg_5v>;
status = "okay";
};
&trng {
status = "okay";
};
&uart0 {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "okay";
};
&usb_phy {
status = "okay";
};
&factory {
@ -554,15 +79,46 @@
#address-cells = <1>;
#size-cells = <1>;
macaddr_factory_0004: macaddr@0004 {
reg = <0x0004 0x6>;
};
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
macaddr_factory_0024: macaddr@0024 {
reg = <0x0024 0x6>;
};
eeprom_factory: eeprom@0 {
#size-cells = <1>;
reg = <0x0 0x1000>;
};
macaddr_factory_002a: macaddr@002a {
reg = <0x002a 0x6>;
macaddr_factory_0004: macaddr@0004 {
compatible = "mac-base";
reg = <0x0004 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_factory_0024: macaddr@0024 {
compatible = "mac-base";
reg = <0x0024 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_factory_002a: macaddr@002a {
compatible = "mac-base";
reg = <0x002a 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_002a 0>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
nvmem-cells = <&macaddr_factory_0024 0>;
nvmem-cell-names = "mac-address";
};
&wifi {
nvmem-cells = <&eeprom_factory>;
nvmem-cell-names = "eeprom";
};

106
target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts Normal file
View File

@ -0,0 +1,106 @@
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
* Copyright (C) 2021 MediaTek Inc.
* Author: Sam.Shih <sam.shih@mediatek.com>
*/
/dts-v1/;
#include "mt7986a.dtsi"
#include "mt7986a-zyxel-ex5601-t0-common.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Zyxel EX5601-T0 ubootmod";
compatible = "zyxel,ex5601-t0-ubootmod", "mediatek,mt7986a";
memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
};
&nand_partitions {
partition@0 {
label = "bl2";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "u-boot-env";
reg = <0x0100000 0x0080000>;
read-only;
};
factory: partition@180000 {
label = "Factory";
reg = <0x180000 0x0200000>;
read-only;
};
partition@380000 {
label = "fip";
reg = <0x380000 0x0200000>;
read-only;
};
partition@540000 {
label = "zloader";
reg = <0x540000 0x0040000>;
read-only;
};
partition@580000 {
label = "ubi";
reg = <0x580000 0x1da80000>;
};
};
&factory {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
eeprom_factory: eeprom@0 {
#size-cells = <1>;
reg = <0x0 0x1000>;
};
macaddr_factory_0004: macaddr@0004 {
compatible = "mac-base";
reg = <0x0004 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_factory_0024: macaddr@0024 {
compatible = "mac-base";
reg = <0x0024 0x6>;
#nvmem-cell-cells = <1>;
};
macaddr_factory_002a: macaddr@002a {
compatible = "mac-base";
reg = <0x002a 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_002a 0>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
nvmem-cells = <&macaddr_factory_0024 0>;
nvmem-cell-names = "mac-address";
};
&wifi {
nvmem-cells = <&eeprom_factory>;
nvmem-cell-names = "eeprom";
};

7
target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
View File

@ -42,6 +42,13 @@ xiaomi,redmi-router-ax6000-stock|\
xiaomi,redmi-router-ax6000-ubootmod)
ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
;;
zyxel_ex5601-t0-stock|\
zyxel,ex5601-t0-ubootmod)
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx"
ucidef_set_led_netdev "wan" "WAN" "green:inet" "eth1" "link tx rx"
ucidef_set_led_netdev "wifi-24g" "WIFI-2.4G" "green:wifi24g" "phy0-ap0" "link tx rx"
ucidef_set_led_netdev "wifi-5g" "WIFI-5G" "green:wifi5g" "phy1-ap0" "link tx rx"
;;
esac
board_config_flush

4
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
View File

@ -73,6 +73,10 @@ mediatek_setup_interfaces()
xiaomi,redmi-router-ax6000-ubootmod)
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan
;;
zyxel,ex5601-t0-stock|\
zyxel,ex5601-t0-ubootmod)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
;;
*)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan
;;

3
target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
View File

@ -107,7 +107,8 @@ case "$board" in
;;
routerich,ax3000|\
zbtlink,zbt-z8102ax|\
zyxel,ex5601-t0)
zyxel,ex5601-t0|\
zyxel,ex5601-t0-ubootmod)
addr=$(mtd_get_mac_binary "Factory" 0x4)
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
;;

5
target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
View File

@ -142,6 +142,11 @@ platform_do_upgrade() {
CI_ROOT_UBIPART=ubi
nand_do_upgrade "$1"
;;
zyxel,ex5601-t0-ubootmod)
CI_KERNPART="fit"
CI_ROOTPART="ubi_rootfs"
nand_do_upgrade "$1"
;;
*)
nand_do_upgrade "$1"
;;

34
target/linux/mediatek/image/filogic.mk
View File

@ -801,10 +801,11 @@ TARGET_DEVICES += zbtlink_zbt-z8102ax
define Device/zyxel_ex5601-t0-stock
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0 (stock layout)
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (stock layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
@ -821,6 +822,35 @@ define Device/zyxel_ex5601-t0-stock
endef
TARGET_DEVICES += zyxel_ex5601-t0-stock
define Device/zyxel_ex5601-t0-ubootmod
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
DEVICE_VARIANT := (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | lzma
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
IMAGE/sysupgrade.itb := append-kernel | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-4k-ddr4
ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot zyxel_ex5601-t0
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += zyxel_ex5601-t0-ubootmod
define Device/zyxel_ex5700-telenor
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := EX5700 (Telenor)