ramips: add support for JCG Q20
JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This commit is contained in:
Chukun Pan
David Bauer
parent
3501db9b9b
commit
57cb387cfe
|
|
@ -43,6 +43,9 @@ ravpower,rp-wd03)
|
|||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000"
|
||||
;;
|
||||
jcg,q20)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
;;
|
||||
linksys,ea7300-v1|\
|
||||
linksys,ea7300-v2|\
|
||||
linksys,ea7500-v2|\
|
||||
|
|
|
|||
|
|
@ -0,0 +1,175 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "jcg,q20", "mediatek,mt7621-soc";
|
||||
model = "JCG Q20";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_red;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_blue;
|
||||
led-upgrade = &led_status_blue;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_red: status_red {
|
||||
label = "red:status";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_blue: status_blue {
|
||||
label = "blue:status";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
ubi-concat {
|
||||
compatible = "mtd-concat";
|
||||
devices = <&ubiconcat0 &ubiconcat1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0 0x5900000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "Config";
|
||||
reg = <0x80000 0x80000>;
|
||||
};
|
||||
|
||||
factory: partition@100000 {
|
||||
label = "Factory";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "kernel";
|
||||
reg = <0x180000 0x400000>;
|
||||
};
|
||||
|
||||
ubiconcat0: partition@580000 {
|
||||
label = "ubiconcat0";
|
||||
reg = <0x580000 0x1c00000>;
|
||||
};
|
||||
|
||||
partition@2180000 {
|
||||
label = "firmware_backup";
|
||||
reg = <0x2180000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@4180000 {
|
||||
label = "rootfs_data_back";
|
||||
reg = <0x4180000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@4200000 {
|
||||
label = "nvram_config";
|
||||
reg = <0x4200000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ubiconcat1: partition@4280000 {
|
||||
label = "ubiconcat1";
|
||||
reg = <0x4280000 0x3d00000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* last 512 KiB are for the bad block table
|
||||
*/
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
mtd-mac-address = <&factory 0x3fff4>;
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
status = "okay";
|
||||
label = "wan";
|
||||
mtd-mac-address = <&factory 0x3fffa>;
|
||||
};
|
||||
|
||||
port@1 {
|
||||
status = "okay";
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
status = "okay";
|
||||
label = "lan2";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "jtag", "wdt";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
|
@ -720,6 +720,23 @@ define Device/jcg_jhr-ac876m
|
|||
endef
|
||||
TARGET_DEVICES += jcg_jhr-ac876m
|
||||
|
||||
define Device/jcg_q20
|
||||
$(Device/dsa-migration)
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 91136k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
||||
check-size
|
||||
DEVICE_VENDOR := JCG
|
||||
DEVICE_MODEL := Q20
|
||||
DEVICE_PACKAGES := kmod-mt7915e uboot-envtools
|
||||
endef
|
||||
TARGET_DEVICES += jcg_q20
|
||||
|
||||
define Device/jcg_y2
|
||||
$(Device/dsa-migration)
|
||||
$(Device/uimage-lzma-loader)
|
||||
|
|
|
|||
|
|
@ -14,6 +14,7 @@ ramips_setup_interfaces()
|
|||
;;
|
||||
asiarf,ap7621-nv1|\
|
||||
glinet,gl-mt1300|\
|
||||
jcg,q20|\
|
||||
lenovo,newifi-d1|\
|
||||
mikrotik,routerboard-m33g|\
|
||||
xiaomi,mi-router-3g|\
|
||||
|
|
|
|||
|
|
@ -14,6 +14,10 @@ case "$board" in
|
|||
[ "$PHYNBR" = "1" ] && \
|
||||
macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
jcg,q20)
|
||||
[ "$PHYNBR" = "1" ] && \
|
||||
macaddr_setbit_la "$(mtd_get_mac_binary Factory 0x4)" > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
linksys,ea7300-v1|\
|
||||
linksys,ea7300-v2|\
|
||||
linksys,ea7500-v2)
|
||||
|
|
|
|||
|
|
@ -49,6 +49,7 @@ platform_do_upgrade() {
|
|||
dlink,dir-2640-a1|\
|
||||
dlink,dir-2660-a1|\
|
||||
hiwifi,hc5962|\
|
||||
jcg,q20|\
|
||||
linksys,ea7300-v1|\
|
||||
linksys,ea7300-v2|\
|
||||
linksys,ea7500-v2|\
|
||||
|
|
|
|||
Loading…
Reference in New Issue