ipq40xx: add support for EnGenius EMD1

SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (1 port)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
Yen-Ting-Shen 2019-11-01 14:00:40 +08:00 committed by Christian Lamparter
parent 52b8c7a892
commit 51f3035978
7 changed files with 263 additions and 1 deletions

View File

@ -28,6 +28,7 @@ ALLWIFIBOARDS:= \
aruba_ap-303 \
avm_fritzrepeater-1200 \
dlink_dap2610 \
engenius_emd1 \
ezviz_cs-w3-wd1200g-eup \
linksys_ea8300 \
qxwlan_e2600ac
@ -96,6 +97,7 @@ endef
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))

Binary file not shown.

View File

@ -49,6 +49,7 @@ ipq40xx_setup_interfaces()
avm,fritzrepeater-1200|\
dlink,dap-2610 |\
engenius,eap1300|\
engenius,emd1|\
meraki,mr33|\
netgear,ex6100v2|\
netgear,ex6150v2|\
@ -108,6 +109,10 @@ ipq40xx_setup_macs()
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
label_mac=$lan_mac
;;
engenius,emd1)
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
label_mac=$lan_mac
;;
engenius,ens620ext)
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)

View File

@ -91,6 +91,10 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
;;
engenius,emd1)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
;;
engenius,ens620ext)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
@ -166,6 +170,10 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
;;
engenius,emd1)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
;;
engenius,ens620ext)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)

View File

@ -0,0 +1,233 @@
// SPDX-License-Identifier: GPL-2.0-or-later
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "EnGenius EMD1";
compatible = "engenius,emd1";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
switch_lan_bmp = <0x20>;
switch_wan_bmp = <0x00>;
};
edma@c080000 {
status = "okay";
qcom,num_gmac = <1>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "emd1:white:power";
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
};
wlan2g {
label = "emd1:red:wlan2g";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tpt";
};
wlan5g {
label = "emd1:blue:wlan5g";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy1tpt";
};
mesh {
label = "emd1:orange:mesh";
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
};
};
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio54", "gpio55", "gpio56", "gpio57";
drive-strength = <12>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio54";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition0@0 {
label = "0:SBL1";
reg = <0x00000000 0x00040000>;
read-only;
};
partition1@40000 {
label = "0:MIBIB";
reg = <0x00040000 0x00020000>;
read-only;
};
partition2@60000 {
label = "0:QSEE";
reg = <0x00060000 0x00060000>;
read-only;
};
partition3@c0000 {
label = "0:CDT";
reg = <0x000c0000 0x00010000>;
read-only;
};
partition4@d0000 {
label = "0:DDRPARAMS";
reg = <0x000d0000 0x00010000>;
read-only;
};
partition5@e0000 {
label = "0:APPSBLENV";
reg = <0x000e0000 0x00010000>;
read-only;
};
partition6@f0000 {
label = "0:APPSBL";
reg = <0x000f0000 0x00080000>;
read-only;
};
partition7@170000 {
label = "0:ART";
reg = <0x00170000 0x00010000>;
read-only;
};
partition8@180000 {
label = "userconfig";
reg = <0x00180000 0x00080000>;
read-only;
};
partition9@200000 {
compatible = "denx,fit";
label = "firmware";
reg = <0x200000 0x01e00000>;
};
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
&gmac0 {
qcom,phy_mdio_addr = <4>;
qcom,poll_required = <1>;
qcom,forced_speed = <1000>;
qcom,forced_duplex = <1>;
vlan_tag = <1 0x20>;
};
&cryptobam {
status = "okay";
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "EnGenius-EMD1";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "EnGenius-EMD1";
};

View File

@ -278,6 +278,19 @@ define Device/engenius_eap1300
endef
TARGET_DEVICES += engenius_eap1300
define Device/engenius_emd1
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EMD1
DEVICE_DTS_CONFIG := config@4
SOC := qcom-ipq4018
IMAGE_SIZE := 30720k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += engenius_emd1
define Device/engenius_ens620ext
$(call Device/FitImage)
DEVICE_VENDOR := EnGenius

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -785,11 +785,41 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -20,6 +20,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
+ qcom-ipq4018-ea6350v3.dtb \
+ qcom-ipq4018-eap1300.dtb \
+ qcom-ipq4018-emd1.dtb \
+ qcom-ipq4018-ens620ext.dtb \
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \