ipq40xx: add support for Buffalo WTR-M2133HP

Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
This commit is contained in:
Yanase Yuki 2020-01-29 19:27:25 +09:00 committed by Petr Štetiar
parent d2c3131b3f
commit 4a77a060ab
11 changed files with 456 additions and 0 deletions

View File

@ -37,6 +37,9 @@ openmesh,a42 |\
openmesh,a62)
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
;;
buffalo,wtr-m2133hp)
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
;;
linksys,ea6350v3)
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
;;

View File

@ -28,6 +28,7 @@ ALLWIFIBOARDS:= \
8dev_habanero-dvk \
aruba_ap-303 \
avm_fritzrepeater-1200 \
buffalo_wtr-m2133hp \
cellc_rtl30vw \
dlink_dap2610 \
engenius_eap2200 \
@ -101,6 +102,7 @@ endef
$(eval $(call generate-ipq-wifi-package,8dev_habanero-dvk,8devices Habanero DVK))
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))

View File

@ -65,6 +65,11 @@ ipq40xx_setup_interfaces()
engenius,eap2200)
ucidef_set_interface_lan "eth0 eth1"
;;
buffalo,wtr-m2133hp)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
;;
cellc,rtl30vw)
ucidef_set_interface_lan "eth0"
ucidef_add_switch "switch0" \

View File

@ -31,6 +31,10 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x9000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
;;
engenius,eap2200 |\
openmesh,a62)
caldata_extract "0:ART" 0x9000 0x2f20
@ -82,6 +86,10 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x26)
;;
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\
@ -171,6 +179,10 @@ case "$FIRMWARE" in
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
buffalo,wtr-m2133hp)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x2c)
;;
cellc,rtl30vw |\
compex,wpj419 |\
compex,wpj428 |\

View File

@ -64,6 +64,7 @@ platform_do_upgrade() {
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000 |\
buffalo,wtr-m2133hp |\
cilab,meshpoint-one |\
engenius,eap2200 |\
mobipromo,cm520-79f |\

View File

@ -0,0 +1,419 @@
// SPDX-License-Identifier: ISC
/*
* Copyright (c) 2015 - 2016, The Linux Foundation. All rights reserved.
* Copyright (c) 2020 Yanase Yuki <dev@zpc.sakura.ne.jp>
*/
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Buffalo WTR-M2133HP";
compatible = "buffalo,wtr-m2133hp", "qcom,ipq4019";
memory {
device_type = "memory";
reg = <0x80000000 0x20000000>;
};
chosen {
/*
* U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs" to
* kernel command line. But we use different partition names,
* so we have to set correct parameters.
*/
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
};
aliases {
led-boot = &led_power_blue;
led-failsafe = &led_power_orange;
led-running = &led_power_white;
led-upgrade = &led_power_blue;
label-mac-device = &gmac0;
};
soc {
rng@22000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
status = "okay";
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
switch_lan_bmp = <0x1c>;
};
ess-psgmii@98000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
usb3@8af8800 {
status = "okay";
};
};
leds {
compatible = "gpio-leds";
led_power_white: power_white {
label = "wtr-m2133hp:white:power";
gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
};
led_power_orange: power_orange {
label = "wtr-m2133hp:orange:power";
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
};
led_power_blue: power_blue {
label = "wtr-m2133hp:blue:power";
gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
};
router_white {
label = "wtr-m2133hp:white:router";
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
};
router_orange {
label = "wtr-m2133hp:orange:router";
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
};
internet_white {
label = "wtr-m2133hp:white:internet";
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
};
internet_orange {
label = "wtr-m2133hp:orange:internet";
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
};
wireless_white {
label = "wtr-m2133hp:white:wireless";
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
};
wireless_orange {
label = "wtr-m2133hp:orange:wireless";
gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
auto_mode {
label = "auto_mode";
gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
router_mode {
label = "router_mode";
gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
ap_mode {
label = "ap_mode";
gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
linux,code = <BTN_2>;
linux,input-type = <EV_SW>;
};
reset {
label = "reset";
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "AOSS Button";
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
};
&tlmm {
serial_0_pins: serial0_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
mdio_pins: mdio_pinmux {
mux_1 {
pins = "gpio6";
function = "mdio";
bias-pull-up;
};
mux_2 {
pins = "gpio7";
function = "mdc";
bias-pull-up;
};
};
nand_pins: nand_pins {
pullups {
pins = "gpio52", "gpio53", "gpio58",
"gpio59";
function = "qpic";
bias-pull-up;
};
pulldowns {
pins = "gpio54", "gpio55", "gpio56",
"gpio57", "gpio60", "gpio61",
"gpio62", "gpio63", "gpio64",
"gpio65", "gpio66", "gpio67",
"gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
usb_power {
line-name = "USB power";
gpios = <34 GPIO_ACTIVE_HIGH>;
gpio-hog;
output-high;
};
};
&blsp_dma {
status = "okay";
};
&blsp1_uart1 {
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
status = "okay";
};
&cryptobam {
status = "okay";
};
&pcie0 {
status = "okay";
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0 0 0 0 0>;
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
};
};
};
&qpic_bam {
status = "okay";
};
&nand {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
status = "okay";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "SBL1";
reg = <0x0000000 0x0100000>;
read-only;
};
partition@100000 {
label = "MIBIB";
reg = <0x0100000 0x0100000>;
read-only;
};
partition@200000 {
label = "BOOTCONFIG";
reg = <0x0200000 0x0100000>;
read-only;
};
partition@300000 {
label = "QSEE";
reg = <0x0300000 0x0100000>;
read-only;
};
partition@400000 {
label = "QSEE_1";
reg = <0x0400000 0x0100000>;
read-only;
};
partition@500000 {
label = "CDT";
reg = <0x0500000 0x0080000>;
read-only;
};
partition@580000 {
label = "CDT_1";
reg = <0x0580000 0x0080000>;
read-only;
};
partition@600000 {
label = "BOOTCONFIG1";
reg = <0x0600000 0x0080000>;
read-only;
};
partition@680000 {
label = "APPSBLENV";
reg = <0x0680000 0x0080000>;
};
partition@700000 {
label = "APPSBL";
reg = <0x0700000 0x0200000>;
read-only;
};
partition@900000 {
label = "APPSBL_1";
reg = <0x0900000 0x0200000>;
read-only;
};
art: partition@b00000 {
label = "ART";
reg = <0x0b00000 0x0080000>;
read-only;
};
partition@b80000 {
label = "ART_1";
reg = <0x0b80000 0x0080000>;
read-only;
};
orgdata: partition@c00000 {
label = "ORGDATA";
reg = <0x0c00000 0x0080000>;
read-only;
};
partition@c80000 {
label = "ORGDATA_1";
reg = <0x0c80000 0x0080000>;
read-only;
};
partition@d00000 {
label = "ubi";
reg = <0x0d00000 0x2900000>;
};
partition@3600000 {
label = "rootfs_recover";
reg = <0x3600000 0x2900000>;
read-only;
};
partition@5f00000 {
label = "user_property";
reg = <0x5f00000 0x1a20000>;
read-only;
};
};
};
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
ieee80211-freq-limit = <2400000 2483000>;
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
};
&mdio {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
};
&gmac0 {
mtd-mac-address = <&orgdata 0x20>;
};
&gmac1 {
mtd-mac-address = <&orgdata 0x20>;
};
&usb3_ss_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};

View File

@ -245,6 +245,18 @@ define Device/avm_fritzrepeater-3000
endef
TARGET_DEVICES += avm_fritzrepeater-3000
define Device/buffalo_wtr-m2133hp
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := WTR-M2133HP
SOC := qcom-ipq4019
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp
BLOCKSIZE := 128k
PAGESIZE := 2048
endef
TARGET_DEVICES += buffalo_wtr-m2133hp
define Device/cellc_rtl30vw
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb

View File

@ -49,6 +49,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4019-wtr-m2133hp.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-ap-303.dtb \
+ qcom-ipq4029-ap-303h.dtb \

View File

@ -50,6 +50,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4019-wtr-m2133hp.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-ap-303.dtb \
+ qcom-ipq4029-ap-303h.dtb \