ath79: Move TPLink WPA8630Pv2 to ath79-tiny target

These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.

Note for users sysupgrading from the previous ath79-generic snapshot
images:

The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.

To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".

If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:

* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message facelift]
(cherry picked from commit 44e1e5d)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit is contained in:
Joe Mullally 2021-08-30 22:35:05 +01:00 committed by Petr Štetiar
parent 41a97c2074
commit 1d4dea6d4f
9 changed files with 96 additions and 42 deletions

View File

@ -348,10 +348,7 @@ tplink,tl-mr6400-v1)
ucidef_set_led_netdev "wan" "WAN" "white:wan" "eth1"
ucidef_set_led_netdev "4g" "4G" "white:4g" "usb0"
;;
tplink,tl-wpa8630-v1|\
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
tplink,tl-wpa8630-v1)
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c"
;;
tplink,tl-wr842n-v2)

View File

@ -382,10 +382,7 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:1" "2:lan:3" "3:lan:2"
;;
tplink,tl-wpa8630-v1|\
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
tplink,tl-wpa8630-v1)
# port 5 (internal) is the power-line port
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4"

View File

@ -228,10 +228,7 @@ case "$FIRMWARE" in
;;
tplink,eap225-outdoor-v1|\
tplink,eap225-v3|\
tplink,eap225-wall-v2|\
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
tplink,eap225-wall-v2)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \

View File

@ -587,36 +587,6 @@ define Device/tplink_tl-wpa8630-v1
endef
TARGET_DEVICES += tplink_tl-wpa8630-v1
define Device/tplink_tl-wpa8630p-v2
$(Device/tplink-safeloader)
SOC := qca9563
DEVICE_MODEL := TL-WPA8630P
IMAGE_SIZE := 6016k
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
define Device/tplink_tl-wpa8630p-v2-int
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2 (Int.)
TPLINK_BOARD_ID := TL-WPA8630P-V2-INT
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2-int
define Device/tplink_tl-wpa8630p-v2.0-eu
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2.0 (EU)
TPLINK_BOARD_ID := TL-WPA8630P-V2.0-EU
SUPPORTED_DEVICES += tplink,tl-wpa8630p-v2-eu
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2.0-eu
define Device/tplink_tl-wpa8630p-v2.1-eu
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2.1 (EU)
TPLINK_BOARD_ID := TL-WPA8630P-V2.1-EU
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2.1-eu
define Device/tplink_tl-wr1043nd-v1
$(Device/tplink-8m)
SOC := ar9132

View File

@ -223,6 +223,41 @@ define Device/tplink_tl-wa901nd-v5
endef
TARGET_DEVICES += tplink_tl-wa901nd-v5
define Device/tplink_tl-wpa8630p-v2
$(Device/tplink-safeloader)
SOC := qca9563
DEVICE_MODEL := TL-WPA8630P
IMAGE_SIZE := 6016k
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := The flash erase blocksize has changed to 4k from the 64k in previous versions, \
so the JFFS2 settings partition MUST be reformatted to avoid data corruption. \
Backup your settings before upgrading, then during sysupgrade, \
de-select "Keep settings" and select "Force" to continue (equivilant to "sysupgrade -n -F").
endef
define Device/tplink_tl-wpa8630p-v2-int
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2 (Int.)
TPLINK_BOARD_ID := TL-WPA8630P-V2-INT
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2-int
define Device/tplink_tl-wpa8630p-v2.0-eu
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2.0 (EU)
TPLINK_BOARD_ID := TL-WPA8630P-V2.0-EU
SUPPORTED_DEVICES += tplink,tl-wpa8630p-v2-eu
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2.0-eu
define Device/tplink_tl-wpa8630p-v2.1-eu
$(Device/tplink_tl-wpa8630p-v2)
DEVICE_VARIANT := v2.1 (EU)
TPLINK_BOARD_ID := TL-WPA8630P-V2.1-EU
endef
TARGET_DEVICES += tplink_tl-wpa8630p-v2.1-eu
define Device/tplink_tl-wr703n
$(Device/tplink-4mlzma)
SOC := ar9331

View File

@ -94,6 +94,11 @@ tplink,tl-wa850re-v2)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "blue:signal4" "wlan0" "60" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "blue:signal5" "wlan0" "80" "100"
;;
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c"
;;
tplink,tl-wr940n-v3|\
tplink,tl-wr940n-v4|\
tplink,tl-wr941nd-v6)

View File

@ -83,6 +83,13 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
;;
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
# port 5 (internal) is the power-line port
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4"
;;
tplink,tl-wr941-v2)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;

View File

@ -0,0 +1,21 @@
#!/bin/sh
#
# Copyright (C) 2020 OpenWrt.org
#
. /lib/functions.sh
. /lib/functions/uci-defaults.sh
board_config_update
case "$(board_name)" in
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
ucidef_set_compat_version "2.0"
;;
esac
board_config_flush
exit 0

View File

@ -0,0 +1,25 @@
#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions/caldata.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
tplink,tl-wpa8630p-v2.1-eu)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) 1)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
esac
;;
*)
exit 1
;;
esac