ipq40xx: add support for Aruba AP-303

Hardware
--------

SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM0
ETH:   Atheros AR8035
LED:   WiFi (amber / green)
       System (red / green)
BTN:   Reset

To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.

Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:

VCC - NC
 D+ - TX
 D- - RX
GND - GND

The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the ethernet port of the access point.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device.

6. Flash OpenWrt:
   $ ubidetach -p /dev/mtd1
   $ ubiformat /dev/mtd1
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
David Bauer 2019-10-23 22:25:14 +02:00
parent 4113d8a255
commit 102c8c55f2
9 changed files with 469 additions and 1 deletions

View File

@ -40,6 +40,7 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
aruba,ap-303|\
avm,fritzrepeater-1200|\
engenius,eap1300|\
meraki,mr33|\

View File

@ -51,6 +51,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x1000 0x2f20
;;
aruba,ap-303)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary mfginfo 0x1D)
;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
@ -116,6 +120,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x5000 0x2f20
;;
aruba,ap-303)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) +1)
;;
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;

View File

@ -2,3 +2,4 @@
::sysinit:/etc/init.d/rcS S boot
::shutdown:/etc/init.d/rcS K shutdown
ttyMSM0::askfirst:/usr/libexec/login.sh
ttyMSM1::askfirst:/usr/libexec/login.sh

View File

@ -4,6 +4,7 @@ set_preinit_iface() {
. /lib/functions.sh
case $(board_name) in
aruba,ap-303| \
asus,rt-ac58u| \
avm,fritzbox-4040| \
glinet,gl-b1300| \

View File

@ -47,6 +47,7 @@ zyxel_do_upgrade() {
platform_do_upgrade() {
case "$(board_name)" in
8dev,jalapeno |\
aruba,ap-303 |\
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000 |\

View File

@ -0,0 +1,419 @@
// SPDX-License-Identifier: GPL-2.0 OR MIT
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Aruba AP-303";
compatible = "aruba,ap-303";
aliases {
led-boot = &led_system_green;
led-failsafe = &led_system_red;
led-running = &led_system_green;
led-upgrade = &led_system_red;
};
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
/delete-node/ ethernet-phy@0;
/delete-node/ ethernet-phy@2;
/delete-node/ ethernet-phy@3;
/delete-node/ ethernet-phy@4;
ethernet-phy@5 {
reg = <0x5>;
};
};
counter@4a1000 {
compatible = "qcom,qca-gcnt";
reg = <0x4a1000 0x4>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
switch_lan_bmp = <0x0>; /* lan port bitmap */
switch_wan_bmp = <0x10>; /* wan port bitmap */
};
edma@c080000 {
qcom,single-phy;
qcom,num_gmac = <1>;
phy-mode = "rgmii-id";
status = "okay";
};
i2c_0: i2c@78b7000 {
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "ok";
tpm@29 {
/* No Driver */
compatible = "atmel,at97sc3203";
reg = <0x29>;
read-only;
};
};
};
leds {
compatible = "gpio-leds";
wifi_green {
label = "ap-303:green:wifi";
gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tpt";
};
wifi_amber {
label = "ap-303:amber:wifi";
gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy1tpt";
};
led_system_red: system_red {
label = "ap-303:red:system";
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
};
led_system_green: system_green {
label = "ap-303:green:system";
gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_uart1 {
/* Texas Instruments CC2540T BLE radio */
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
status = "okay";
};
&blsp1_uart2 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
status = "okay";
};
&cryptobam {
status = "okay";
};
&gmac0 {
qcom,phy_mdio_addr = <5>;
qcom,poll_required = <1>;
vlan_tag = <0 0x20>;
};
&qpic_bam {
status = "okay";
};
&tlmm {
/*
* In addition to the Pins listed below,
* the following GPIOs have "features":
* 54 - out - active low to force HW reset
* 41 - out - active low to reset TPM
* 43 - out - active low to reset BLE radio
* 19 - in - active high when DC powered
*/
mdio_pins: mdio_pinmux {
mux_1 {
pins = "gpio6";
function = "mdio";
bias-pull-up;
};
mux_2 {
pins = "gpio7";
function = "mdc";
bias-pull-up;
};
};
nand_pins: nand_pins {
pullups {
pins = "gpio53", "gpio58", "gpio59";
function = "qpic";
bias-pull-up;
};
pulldowns {
pins = "gpio54", "gpio55", "gpio56",
"gpio57", "gpio60", "gpio61",
"gpio62", "gpio63", "gpio64",
"gpio65", "gpio66", "gpio67",
"gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
spi_0_pins: spi_0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio13", "gpio14", "gpio15";
drive-strength = <12>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio12";
drive-strength = <2>;
bias-disable;
output-high;
};
};
i2c_0_pins: i2c_0_pinmux {
mux {
pins = "gpio10", "gpio11";
function = "blsp_i2c0";
drive-strength = <4>;
bias-disable;
};
};
serial_0_pins: serial_0_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
serial_1_pins: serial_1_pinmux {
mux {
pins = "gpio8", "gpio9";
function = "blsp_uart1";
bias-disable;
};
};
phy-reset {
line-name = "PHY-reset";
gpios = <42 GPIO_ACTIVE_HIGH>;
gpio-hog;
output-high;
};
};
&nand {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
status = "okay";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
/* 'aos0' in Aruba firmware */
label = "aos0";
reg = <0x0 0x2000000>;
read-only;
};
partition@2000000 {
/* 'aos1' in AVM firmware */
label = "ubi";
reg = <0x2000000 0x2000000>;
};
partition@4000000 {
label = "aruba-ubifs";
reg = <0x4000000 0x4000000>;
read-only;
};
};
};
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
/*
* There is no partition map for the NOR flash
* in the stock firmware.
*
* All partitions here are based on offsets
* found in the U-Boot GPL code and information
* from smem.
*/
partition@0 {
label = "sbl1";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "mibib";
reg = <0x40000 0x20000>;
read-only;
};
partition@60000 {
label = "qsee";
reg = <0x60000 0x60000>;
read-only;
};
partition@c0000 {
label = "cdt";
reg = <0xc0000 0x10000>;
read-only;
};
partition@d0000 {
label = "ddrparams";
reg = <0xd0000 0x10000>;
read-only;
};
partition@e0000 {
label = "ART";
reg = <0xe0000 0x10000>;
read-only;
};
partition@f0000 {
label = "appsbl";
reg = <0xf0000 0xf0000>;
read-only;
};
partition@1e0000 {
label = "mfginfo";
reg = <0x1e0000 0x10000>;
read-only;
};
partition@1f0000 {
label = "apcd";
reg = <0x1f0000 0x10000>;
read-only;
};
partition@200000 {
label = "osss";
reg = <0x200000 0x180000>;
read-only;
};
partition@380000 {
/* This is empty */
label = "appsblenv";
reg = <0x380000 0x10000>;
read-only;
};
partition@390000 {
label = "pds";
reg = <0x390000 0x10000>;
read-only;
};
partition@3a0000 {
label = "fcache";
reg = <0x3a0000 0x10000>;
read-only;
};
partition@3b0000 {
/* Called osss1 in smem */
label = "u-boot-env-bak";
reg = <0x3b0000 0x10000>;
read-only;
};
partition@3f0000 {
label = "u-boot-env";
reg = <0x3f0000 0x10000>;
read-only;
};
};
};
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Aruba-AP-303";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Aruba-AP-303";
};

View File

@ -91,6 +91,16 @@ define Device/alfa-network_ap120c-ac
endef
TARGET_DEVICES += alfa-network_ap120c-ac
define Device/aruba_ap-303
$(call Device/FitImageLzma)
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-303
DEVICE_DTS := qcom-ipq4029-ap-303
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += aruba_ap-303
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_VENDOR := ASUS

View File

@ -0,0 +1,26 @@
From 158acdbf0336f601971637f988b57a6a67a0869b Mon Sep 17 00:00:00 2001
From: David Bauer <mail@david-bauer.net>
Date: Sun, 15 Dec 2019 13:10:50 +0100
Subject: [PATCH] mtd: spi-nor: Add support for mx25r3235f
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Signed-off-by: David Bauer <mail@david-bauer.net>
---
drivers/mtd/spi-nor/spi-nor.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1091,6 +1091,8 @@ static const struct flash_info spi_nor_i
{ "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+ { "mx25r3235f", INFO(0xc22816, 0, 64 * 1024, 64,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
{ "mx25u12835f", INFO(0xc22538, 0, 64 * 1024, 256,
SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -785,11 +785,37 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -785,11 +785,38 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@ -43,6 +43,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-unielec-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-ap-303.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \