ipq806x: add support for GL.iNet GL-B1300

This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
This commit is contained in:
Dongming Han 2017-12-07 20:48:19 +08:00 committed by John Crispin
parent 88a41074e8
commit 04d3308b62
8 changed files with 341 additions and 2 deletions

View File

@ -13,7 +13,7 @@ endef
define Build/Compile
endef
ALLWIFIBOARDS:=avm_fritzbox-4040
ALLWIFIBOARDS:=avm_fritzbox-4040 glinet_gl-b1300
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@ -48,5 +48,6 @@ Don't install it for any other device!
endef
$(eval $(call generate-ipq-wifi-package,avm_fritzbox-4040,board-avm_fritzbox-4040.bin,AVM FRITZ!Box 4040))
$(eval $(call generate-ipq-wifi-package,glinet_gl-b1300,board-glinet_gl-b1300.bin,GL.iNet GL-B1300))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))

Binary file not shown.

View File

@ -16,6 +16,9 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
glinet,gl-b1300)
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
;;
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\

View File

@ -33,6 +33,7 @@ tplink,vr2600v)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
glinet,gl-b1300 |\
openmesh,a42)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;

View File

@ -53,6 +53,7 @@ case "$FIRMWARE" in
openmesh,a42)
ath10kcal_extract "0:ART" 4096 12064
;;
glinet,gl-b1300 |\
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 4096 12064
;;
@ -66,6 +67,7 @@ case "$FIRMWARE" in
openmesh,a42)
ath10kcal_extract "0:ART" 20480 12064
;;
glinet,gl-b1300 |\
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 20480 12064
;;

View File

@ -0,0 +1,316 @@
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "GL.iNet GL-B1300";
compatible = "glinet,gl-b1300", "qcom,ipq4019";
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
reserved-memory {
#address-cells = <0x1>;
#size-cells = <0x1>;
ranges;
apps_bl@87000000 {
reg = <0x87000000 0x400000>;
no-map;
};
sbl@87400000 {
reg = <0x87400000 0x100000>;
no-map;
};
cnss_debug@87500000 {
reg = <0x87500000 0x600000>;
no-map;
};
cpu_context_dump@87b00000 {
reg = <0x87b00000 0x080000>;
no-map;
};
tz_apps@87b80000 {
reg = <0x87b80000 0x280000>;
no-map;
};
smem@87e00000 {
reg = <0x87e00000 0x080000>;
no-map;
};
tz@87e80000 {
reg = <0x87e80000 0x180000>;
no-map;
};
};
soc {
tcsr@194b000 {
/* select hostmode */
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
status = "ok";
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
pinctrl@1000000 {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
pinmux {
function = "blsp_spi0";
pins = "gpio55", "gpio56", "gpio57";
};
pinmux_cs {
function = "gpio";
pins = "gpio54";
};
pinconf {
pins = "gpio55", "gpio56", "gpio57";
drive-strength = <12>;
bias-disable;
};
pinconf_cs {
pins = "gpio54";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
blsp_dma: dma@7884000 {
status = "ok";
};
spi_0: spi@78b5000 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "ok";
cs-gpios = <&tlmm 54 0>;
};
serial@78af000 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "ok";
};
cryptobam: dma@8e04000 {
status = "ok";
};
crypto@8e3a000 {
status = "ok";
};
watchdog@b017000 {
status = "ok";
};
usb3_ss_phy: ssphy@9a000 {
status = "ok";
};
usb3_hs_phy: hsphy@a6000 {
status = "ok";
};
usb3: usb3@8af8800 {
status = "ok";
};
usb2_hs_phy: hsphy@a8000 {
status = "ok";
};
usb2: usb2@60f8800 {
status = "ok";
};
mdio@90000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
wifi@a000000 {
status = "okay";
};
wifi@a800000 {
status = "okay";
};
};
gpio-keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power {
label = "gl-b1300:green:power";
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
mesh {
label = "gl-b1300:green:mesh";
gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
};
wlan {
label = "gl-b1300:green:wlan";
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
};
};
};
&spi_0 {
mx25l25635f@0 {
compatible = "mx25l25635f", "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
reg = <0>;
spi-max-frequency = <24000000>;
SBL1@0 {
label = "SBL1";
reg = <0x0 0x40000>;
read-only;
};
MIBIB@40000 {
label = "MIBIB";
reg = <0x40000 0x20000>;
read-only;
};
QSEE@60000 {
label = "QSEE";
reg = <0x60000 0x60000>;
read-only;
};
CDT@c0000 {
label = "CDT";
reg = <0xc0000 0x10000>;
read-only;
};
DDRPARAMS@d0000 {
label = "DDRPARAMS";
reg = <0xd0000 0x10000>;
read-only;
};
APPSBLENV@e0000 {
label = "APPSBLENV";
reg = <0xe0000 0x10000>;
read-only;
};
APPSBL@f0000 {
label = "APPSBL";
reg = <0xf0000 0x80000>;
read-only;
};
ART@170000 {
label = "ART";
reg = <0x170000 0x10000>;
read-only;
};
kernel@180000 {
label = "kernel";
reg = <0x180000 0x400000>;
};
rootfs@580000 {
label = "rootfs";
reg = <0x580000 0x1a80000>;
};
firmware@180000 {
label = "firmware";
reg = <0x180000 0x1e80000>;
};
};
};
&gmac0 {
qcom,phy_mdio_addr = <4>;
qcom,poll_required = <1>;
qcom,forced_speed = <1000>;
qcom,forced_duplex = <1>;
vlan_tag = <2 0x20>;
};
&gmac1 {
qcom,phy_mdio_addr = <3>;
qcom,poll_required = <1>;
qcom,forced_speed = <1000>;
qcom,forced_duplex = <1>;
vlan_tag = <1 0x10>;
};

View File

@ -165,6 +165,21 @@ define Device/netgear_r7800
endef
TARGET_DEVICES += netgear_r7800
define Device/glinet_gl-b1300
DEVICE_TITLE := GL.iNet GL-B1300
BOARD_NAME := gl-b1300
DEVICE_DTS := qcom-ipq4019-gl-b1300
KERNEL_LOADADDR := 0x80208000
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ipq-wifi-glinet_gl-b1300
endef
TARGET_DEVICES += glinet_gl-b1300
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4019-a42

View File

@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -616,9 +616,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -616,9 +616,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4019-a42.dtb \
+ qcom-ipq4019-gl-b1300.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c1.dtb \
+ qcom-ipq4019-fritz4040.dtb \