mirror
/
openwrt
mirror of https://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Releases Activity
openwrt/target/linux/ipq40xx/base-files/etc/board.d/02_network

108 lines
2.4 KiB
Plaintext
Raw Normal View History

ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 20:40:50 +01:00
#!/bin/sh
#
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
# Copyright (c) 2011-2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
ipq40xx_setup_interfaces()
{
local board="$1"
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 20:40:50 +01:00
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
case "$board" in
ipq40xx: add support for ALFA Network AP120C-AC ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-01-29 18:12:51 +01:00
8dev,jalapeno|\
ipq40xx: add support for EnGenius ENS620EXT Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-27 23:48:23 +01:00
alfa-network,ap120c-ac|\
engenius,ens620ext)
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
ipq40xx: add support for ASUS Lyra SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-12 17:19:51 +01:00
asus,map-ac2200|\
openmesh,a42|\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
asus,rt-ac58u|\
ipq40xx: fix ASUS RT-AC58U switch port numbering This patch fixes the ASUS' RT-AC58U port order by unifying the configuration with the NBG6617. Reported-by: Roberto Socrates (rtac58u-user on the forum) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:29:32 +01:00
zyxel,nbg6617)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
avm,fritzbox-4040|\
ipq40xx: Add support for Linksys EA8300 (Dallas) The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-10 17:34:28 +02:00
linksys,ea6350v3|\
linksys,ea8300)
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
ipq40xx: add support for FritzBox 7530 Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-18 23:58:34 +01:00
avm,fritzbox-7530)
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
ipq40xx: add support for AVM FRITZ!Repeater 1200 Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-10 21:07:23 +02:00
avm,fritzrepeater-1200|\
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
engenius,eap1300|\
meraki,mr33|\
netgear,ex6100v2|\
netgear,ex6150v2|\
zyxel,wre6606)
ucidef_set_interface_lan "eth0"
;;
ipq40xx: add support for AVM FRITZ!Repeater 1200 Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-10 21:07:23 +02:00
avm,fritzrepeater-3000|\
ipq40xx: ipq4019: Add new device Compex WPJ419 This device contains 2 flash devices. One NOR (32M) and one NAND (128M). U-boot and caldata are on the NOR, the firmware on the NAND. SoC: IPQ4019 CPU: 4x 710MHz ARMv7 RAM: 256MB FLASH: NOR:32MB NAND:128MB ETH: 2x GMAC Gigabit POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V) WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO 1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO USB: 1x 3.0 PCI: 1x Mini PCIe SIM: 1x Slot SD: 1x MicroSD slot BTN: Reset LED: - Power - Ethernet UART: 1x Serial Port 4 Pin Connector (UART) 1x Serial Port 6 Pin Connector (High Speed UART) POWER: 12V 2A Installation ------------ Initial flashing can only be done via u-boot using the following commands: tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi nand erase.chip; nand write ${fileaddr} 0x0 ${filesize} res Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-01 12:27:13 +01:00
compex,wpj419|\
ipq40xx: add support for AVM FRITZ!Repeater 1200 Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-10 21:07:23 +02:00
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
glinet,gl-b1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan" "4:lan"
;;
ipq40xx: add support for Qxwlan E2600AC C1 and C2 Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-21 06:28:32 +01:00
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
;;
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 11:33:13 +02:00
unielec,u4019-32m)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
;;
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
*)
echo "Unsupported hardware. Network interfaces not initialized"
;;
esac
}
ipq40xx_setup_macs()
{
local board="$1"
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 20:40:50 +01:00
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
case "$board" in
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
treewide: convert MAC address location offsets to hexadecimal This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-09 17:45:12 +02:00
wan_mac=$(mtd_get_mac_binary_ubi Factory 0x5006)
lan_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
;;
ipq40xx: add support for EnGenius ENS620EXT Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-27 23:48:23 +01:00
engenius,ens620ext)
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
linksys,ea6350v3)
wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3 This commit fixes the script that sets the MAC address of the LAN switch. The LAN MAC address should be the WAN MAC address plus one. Without this patch the WAN and the LAN interface will use the same MAC address and an error will be generated. With this patch all interfaces will have a different MAC address, consecutive in the following order: WAN, LAN, radio0 and radio1. Signed-off-by: Oever González <notengobattery@gmail.com>
2019-02-14 01:13:07 +01:00
lan_mac=$(macaddr_add "$wan_mac" 1)
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
;;
esac
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 20:40:50 +01:00
ipq40xx: tidy up 02_networks - fix linksys' EA6350v3 order - remove whitespace that should have been tabs Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-09 18:08:55 +01:00
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
ipq40xx: consolidate 02_network board defaults This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-31 22:23:53 +01:00
}
board_config_update
board=$(board_name)
ipq40xx_setup_interfaces $board
ipq40xx_setup_macs $board
ipq40xx: add target Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
2018-02-21 20:40:50 +01:00
board_config_flush
exit 0