mirror
/
openwrt
mirror of https://git.openwrt.org/openwrt/openwrt.git
1
0
Fork 0
Code Releases Activity
openwrt/package/firmware/ipq-wifi/Makefile

136 lines
4.8 KiB
Makefile
Raw Normal View History

firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/version.mk
ipq-wifi: fix missing define of PKG_NAME Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2017-09-20 04:20:09 +02:00
PKG_NAME:=ipq-wifi
ipq-wifi: fix upstream board-2.bin ZTE M289F snafu The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-07-04 20:42:22 +02:00
PKG_RELEASE:=2
firmware: ipq-wifi: use project branch and drop local file Source BDF files out of project dedicated repository and drop local file from openwrt main repository. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-03-04 11:38:32 +01:00
PKG_SOURCE_PROTO:=git
Revert "WIP: ipq-wifi: use my fork temporarily until upstreamed" This reverts commit 1bad93c42669061b0248ca5cff1d83e399a2ef1a as this was commited by accident, its still work in progress. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-06-05 11:45:24 +02:00
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
ipq-wifi: update to version 2023-06-03 Contains following updates: * ipq8074: update RegDB in new submitted BDF * Revert "ipq8074: update RegDB in new submitted BDF" * qcn9074: update RegDB in new submitted BDF * ipq8074: update RegDB in new submitted BDF * qca-wireless: ipq40xx: add BDFs for ZTE MF287+ * Add BDFs for prpl Foundation Haze board Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-06-05 12:06:41 +02:00
PKG_SOURCE_DATE:=2023-06-03
PKG_SOURCE_VERSION:=cd9c30ca47b8e5388b770c523a7f6b8b969e2f92
PKG_MIRROR_HASH:=45e623fcc512b514ade0f22e217275536aa8de4afba7dfdb11696482b8fa71a2
firmware: ipq-wifi: use project branch and drop local file Source BDF files out of project dedicated repository and drop local file from openwrt main repository. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-03-04 11:38:32 +01:00
firmware: ipq-wifi: mark packages as nonshared The board-files are specific to the target and device. Hence they need to be set as nonshared. Otherwise they do not show up on the package repository. This causes problems for imagebuilder, if it needs to build a image for a specific device that hasn't had the time to have get its boardfile upstream. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-17 18:11:59 +01:00
PKG_FLAGS:=nonshared
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
include $(INCLUDE_DIR)/package.mk
define Build/Compile
endef
ipq40xx: Add support for D-Link DAP-2610 Specifications ============== - SOC: IPQ4018 - RAM: DDR3 256MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11 - 5GHz: IPQ4018, 2x2, front end SKY85717-21 - Ethernet: 1x 10/100/1000Mbps, POE 802.3af - PHY: QCA8072 - UART: GND, blocked, 3.3V, RX, TX / 115200 8N1 - LED: 1x red / green - Button: 1x reset / factory default - U-Boot bootloader with tftp and "emergency web server" accessible using serial port. Installation ============ Flash factory image from D-Link web UI. Constraints in the D-Link web UI makes the factory image unnecessarily large. Flash again using sysupgrade from inside OpenWrt to reclaim some flash space. Return to stock D-Link firmware =============================== Partition layout is preserved, and it is possible to return to the stock firmware simply by downloading it from D-Link and writing it to the firmware partition. # mtd -r write dap2610-firmware.bin firmware Quirks ====== To be flashable from the D-Link http server, the firmware must be larger then 6MB, and the size in the firmware header must match the actual file size. Also, the boot loader verifies the checksum of the firmware before each boot, thus the jffs2 must be after the checksum covered part. This is solved in the factory image by having the rootfs at the very end of the image (without pad-rootfs). The sysupgrade image which does not have to be flashable from the D-Link web UI may be smaller, and the checksum in the firmware header only covers the kernel part of the image. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> [added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux, added emd1's gmac0 config,fix dtc warnings] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-10 11:25:53 +02:00
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
# to generate the board-* files here.
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
#
# This is intended to be used on an interim basis until device-specific
# board data for new devices is available through the upstream compilation
#
ipq-wifi: add a note / reminder about upstreaming new board files |Please send a mail with your device-specific board files upstream. |You can find instructions and examples on the linux-wireless wiki: |<https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-29 11:55:13 +02:00
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
ALLWIFIBOARDS:= \
ipq807x: add support for Buffalo WXR-5950AX12 Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-23 05:01:13 +01:00
buffalo_wxr-5950ax12 \
ipq-wifi: bump to latest git HEAD 0f73d32 ipq8074: update RegDB in new submitted BDF a4cd21f ipq8074: add Compex WPQ873 BDF c888dd0 qca-wireless: ipq40xx: Add BDFs for Eero Cento 6388ba9 ipq8074: update regdb for Netgear SXK80 BDF 77775d2 ipq8074: add Netgear SXK80 Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
2023-05-25 08:43:46 +02:00
compex_wpq873 \
ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-08-05 11:38:37 +02:00
dynalink_dl-wrx36 \
ipq807x: add Edgecore EAP102 The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-01-29 01:03:11 +01:00
edgecore_eap102 \
ipq807x: add Edimax CAX1800 Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 23:17:51 +01:00
edimax_cax1800 \
ipq807x: add support for Netgear WAX218 Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
2022-06-02 18:35:26 +02:00
netgear_wax218 \
ipq-wifi: update to version 2023-06-03 Contains following updates: * ipq8074: update RegDB in new submitted BDF * Revert "ipq8074: update RegDB in new submitted BDF" * qcn9074: update RegDB in new submitted BDF * ipq8074: update RegDB in new submitted BDF * qca-wireless: ipq40xx: add BDFs for ZTE MF287+ * Add BDFs for prpl Foundation Haze board Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-06-05 12:06:41 +02:00
prpl_haze \
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 23:20:19 +01:00
qnap_301w \
ipq807x: add Redmi AX6 Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
2022-01-01 23:12:51 +01:00
redmi_ax6 \
ipq40xx: add support for Wallystech DR40x9 Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2020-06-30 18:07:50 +02:00
wallys_dr40x9 \
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
xiaomi_ax3600 \
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-11 00:50:37 +01:00
xiaomi_ax9000 \
ipq-wifi: fix upstream board-2.bin ZTE M289F snafu The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-07-04 20:42:22 +02:00
zte_mf289f \
ipq4019: add support for ZTE MF287+ aka DreiNeo The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-07 21:24:18 +02:00
zte_mf287plus \
ipq807x: Add ZyXEL NBG7815 ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-03 19:23:41 +01:00
zyxel_nbg7815
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
SUBMENU:=ath10k Board-Specific Overrides
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
SECTION:=firmware
CATEGORY:=Firmware
ipq807x: rename target to qualcommax Currently, ipq807x only covers Qualcomm IPQ807x SoC-s. However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid duplicating kernel patches and everything lets make a common target with per SoC subtargets. Start doing that by renaming ipq807x to qualcommax so that dependencies on ipq807x target can be updated. Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-11 19:32:52 +02:00
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_qualcommax)
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
TITLE:=Custom Board
endef
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
define ipq-wifi-install-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
endef
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
define ipq-wifi-install-ath11-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
endef
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
define ipq-wifi-install-one
ipq-wifi: drop deprecated .bin support This patch converts the Qxwlan E2600AC image away from the deprecated .bin file and to the new .qca4019 method. As a result, we no longer need to carry around the legacy support for handling .bin files. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-19 00:00:52 +01:00
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
ipq40xx: Add support ZTE MF18A Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 19:01:40 +01:00
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-11 00:50:37 +01:00
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-11 00:50:37 +01:00
)))))))
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
endef
# Blank line required at end of above define due to foreach context
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
define generate-ipq-wifi-package
define Package/ipq-wifi-$(1)
$(call Package/ipq-wifi-default)
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
TITLE:=board-2.bin Overrides for $(2)
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
CONFLICTS:=$(PREV_BOARD)
endef
define Package/ipq-wifi-$(1)/description
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
The $(2) requires board-specific, reference ("cal") data
that is not yet present in the upstream wireless firmware distribution.
This package supplies board-2.bin file(s) that, in the interim,
overwrite those supplied by the ath10k-firmware-* packages.
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
This is package is only necessary for the $(2).
Do not install it for any other device!
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
endef
define Package/ipq-wifi-$(1)/install-overlay
firmware: ipq-wifi: use project branch and drop local file Source BDF files out of project dedicated repository and drop local file from openwrt main repository. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-03-04 11:38:32 +01:00
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard $(PKG_BUILD_DIR)/board-$(1).*),\
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
endef
PREV_BOARD+=ipq-wifi-$(1)
endef
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
# Add board name to ALLWIFIBOARDS
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
firmware/ipq-wifi: Extend for multi-chip boards This package provides board-specific reference ("cal") data on an interim basis until included in the upstream distros While originally conceived for IPQ4019-based boards, similar needs are appearing with three-radio devices. For some of these devices, both a board-2.bin file needs to be supplied both for the IPQ4019 as well as for the other radio on the board. This patch allows new or multiple overrides to be specified by: * Adding board name to ALLWIFIBOARDS * Placing file(s) in this directory named as board-<devicename>.<qca4019|qca9888|qca9984> * Adding $(eval $(call generate-ipq-wifi-package,<device>,<display name>)) (along with suitable package selection for the board) At this time, QCA4019, QCA9888, and QCA9984 are supported. Extension to other chips should be straightforward. The existing files, board-*.bin, are "grandfathered" as QCA4019. The package name has been retained for compatability reasons. At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility. Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac, avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300, engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-14 22:20:57 +02:00
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
ipq807x: add support for Buffalo WXR-5950AX12 Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-23 05:01:13 +01:00
$(eval $(call generate-ipq-wifi-package,buffalo_wxr-5950ax12,Buffalo WXR-5950AX12))
ipq-wifi: bump to latest git HEAD 0f73d32 ipq8074: update RegDB in new submitted BDF a4cd21f ipq8074: add Compex WPQ873 BDF c888dd0 qca-wireless: ipq40xx: Add BDFs for Eero Cento 6388ba9 ipq8074: update regdb for Netgear SXK80 BDF 77775d2 ipq8074: add Netgear SXK80 Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
2023-05-25 08:43:46 +02:00
$(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873))
ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-08-05 11:38:37 +02:00
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
ipq807x: add Edgecore EAP102 The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-01-29 01:03:11 +01:00
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
ipq807x: add Edimax CAX1800 Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 23:17:51 +01:00
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
ipq807x: add support for Netgear WAX218 Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
2022-06-02 18:35:26 +02:00
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 23:20:19 +01:00
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
ipq-wifi: update to version 2023-06-03 Contains following updates: * ipq8074: update RegDB in new submitted BDF * Revert "ipq8074: update RegDB in new submitted BDF" * qcn9074: update RegDB in new submitted BDF * ipq8074: update RegDB in new submitted BDF * qca-wireless: ipq40xx: add BDFs for ZTE MF287+ * Add BDFs for prpl Foundation Haze board Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-06-05 12:06:41 +02:00
$(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
ipq807x: add Redmi AX6 Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
2022-01-01 23:12:51 +01:00
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
ipq40xx: add support for Wallystech DR40x9 Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2020-06-30 18:07:50 +02:00
$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 21:04:43 +02:00
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-11 00:50:37 +01:00
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
ipq-wifi: fix upstream board-2.bin ZTE M289F snafu The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-07-04 20:42:22 +02:00
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
ipq4019: add support for ZTE MF287+ aka DreiNeo The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-07 21:24:18 +02:00
$(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
ipq807x: Add ZyXEL NBG7815 ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-03 19:23:41 +01:00
$(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 11:49:14 +01:00
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))