For some purposes (e.g. SNAT, vxlan) it might be necessary to have an
additional address just for the router which is not attached to any
interfaces. Addresses like this are typically added to the loopback
interface.
The new options "router_ip" and "router_ip6" are added to the gateway
config to allow the user to configure such addresses. It is possible to
both specify the address with or without a subnet size.
The default configuration contains the IPv4 loopback address
(127.0.0.1/8) explicitly, but this is not necessary. These addresses are
configured automatically, even if they are not present in the
configuration, so they can safely be removed, if present.
The filters of our routing daemon babeld are adjusted accordingly, so
the newly added addresses are announced correctly.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Starting with OpenWrt 21.02 some devices now use upstream kernel drivers
for the built-in switch instead of relying on OpenWrt's swconfig driver.
The upstream kernel drivers use the Distributed Switch Architecture
(DSA) for configuration of the switch. Instead of explicitly configuring
the hardware switch, all ports appear as distinct interfaces and linux
bridges are offloaded to the hardware switch if possible.
To keep changes small, this patch adds support for DSA devices by
setting up a linux bridge, which is then treated just like the
cpuport-interface of the swconfig driver.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Tested-by: Fabian Bläse <fabian@blaese.de>
Allow setting WAN vlan/interface from gateway config.
A configuration without explicit definition of a WAN interface is
valid at the moment and results in the default configuration from
fff-network being used.
Originally, it was intended to automatically set WAN to vlan 2, if nothing was
specified. As this would break devices, which don't use swconfig for
WAN, the already configured WAN interface is left untouched.
Fixes: #85 (gitea)
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Instead of exposing the CPUPORT variable to the calling script
directly, wrap it into a function which can be called there.
Fixes: #52 (gitea)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
The name br-mesh is actually quite misleading, since the bridge
actually includes the "client" interfaces. In order to make this
obvious, and to prevent confusion with the properly named wXmesh
interfaces, rename them to br-client.
Note that br-mesh is also particularly disturbing for the layer 3
firmware without batman-adv.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Fabian Bläse <fabian@blaese.de>
Acked-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
configuregateway and it's gateway.d files represent a specific
functionality that other packages depend on. Thus, it is put into
a package of its own so dependencies can be expressed more properly.
While at, use the chance to get rid of the ambiguous term "gateway"
and rename the script to configure-layer3 and the folders to layer3.d.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <freifunk@dresel.systems>
Fabian Bläse
Adrian Schmutzler