The ethernet MAC addresses of the Archer C60 v1/v2 were swapped
compared to the vendor assignment. This has been fixed in OpenWrt
after 19.07.2.
Apply this to our firmware already, so we cannot forget it later
and prevent having messed-up br-mesh MAC addresses.
The OpenWrt patches can be removed again when bumping to 19.07.3.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
At the moment, the ETHMESHMAC for the TL-WR1043ND v4 is loaded from
the config partition. The data there is written by the stock firmware,
and thus is dependent on the version installed before and may even
vary in position.
Instead, this patch uses the product-info partition, which is not
modified by stock firmware.
While at it, update the sourced library files and the comment for
both v4 and v5.
ref: 53839da46e
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
In OpenWrt commit 27eea249213b ("ar71xx: fix MAC address setup for
TL-WDR4300 board") the LAN/WAN MAC addresses for the TL-WDR3600,
TL-WDR4300 and TL-WDR4310 were changed.
This creates an overlap of the LAN und 5 GHz MAC addresses, where
the first will also affect the BATMAN interface eth0.3.
To keep BATMAN interfaces with separate addresses, this patch will
set the ETHMESHMAC to eth0 +1, corresponding to the virtual WAN device
(VLAN 2) OpenWrt sets up (which we aren't using anyway).
ref: https://github.com/openwrt/openwrt/commit/27eea249213b04a372491009850926f9282d13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
In OpenWrt commit 8a21bc36229d ("ar71xx: fix MAC addresses for
Archer C5 v1, C7 v1/v2, WDR4900 v2") the WiFi MAC addresses for
the Archer C7 v2 were changed.
This creates an overlap of the LAN und 2.4 GHz MAC addresses, where
the first will also affect the BATMAN interface eth1.3.
To keep BATMAN interfaces with separate addresses, this patch will
set the ETHMESHMAC from eth0, corresponding to the separate WAN
device we are not using in our firmware anyway.
ref: https://github.com/openwrt/openwrt/commit/8a21bc36229d3eabad213ae47fddb4d86d76ac
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
This migrates to the new configuration architecture introduced
and required in
54af5a209e
This is a side-effect of the switch to openwrt-19.07.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fabian@blaese.de: Rebase onto fff firmware master]
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Previously the TP-Link Archer C7v2 was configured to use
two Switch CPU Interfaces. One for Trunk (Client + Batman), one
for WAN.
As this setup is very uncommon in our firmware at the moment and does interfere
with the automatic CPU Port setup in layer3 variant, it is converted to a single
trunk port setup just like all of the other routers with integrated managed switches.
As eth0 is now used as the switchport, this change would require to setup
a different ETHMESHMAC if mac addresses would be shared between interfaces.
The device does seems to have 4 discrete mac addresses however, so the
explicit ETHMESHMAC setting is completely removed instead.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
As odhcpd is used as router advertisement server in layer3 variant,
but configurenetwork is still necessary, the dependency to fff-uradvd has
to be removed.
This is done by first checking, if the fff-uradvd service exists, before it
is restarted.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
On layer3 variant ("gateway firmware"), 60-fff-gateway.conf
changes "forwarding" for all interfaces, overwriting the
changes from 51-fff-network-$iface.conf.
By putting the WAN-specific commands after 60-fff-gateway.conf
this patch should provide the correct device-specific value
for WAN interface now.
Signed-off-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[Rephrased commit title and added message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This interface was using 1500 anyway and setting ethernet to
MTU > 1500 might not be a good idea.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langammer <rlanghammer@web.de>
This provides the CPUPORT which is needed for the gateway firmware.
The script is supposed to be sourced.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
This fixes a typo in description and introduces a single variable
for the sysctlfile.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Currently, Makefile use a mixture of tabs and spaces with various
indents. This harmonizes all Makefiles to use tab indentation only.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
tcp timestamps can improve tcp performance a lot, especially
with unstable networks like wifi.
Linux default behaviour is enabled so the tcp timestamps setting
is removed from sysctl configuration.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
This device is still in PR state in OpenWrt, since ar71xx target
is deprecated and thus lacking reviewers.
It worked nicely for me anyway, so I include the current state of
the PR (has not changed for months).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
With our dynamic resetting of WiFi interfaces, the rssileds
of OpenWrt do not work correctly. This disables them as a
workaround, since they otherwise create about 20 % CPU load.
Since the MACH file for all CPE210/510 is the same, no adjustment
of the OpenWrt-tiny patch is needed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
When setting up a node, router solicitations can be used to speed
up receiving router advertisements a lot. This mechanism has been
previously disabled by our custom sysctl config.
However because linux does not send router solicitations, if it
doesn't accept router advertisements, which is disabled for every
link except WAN, this option can safely be set to it's default value
for all interfaces.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
The V2 firmware requires initialization of the WiFi interfaces
by a hood file. If a one-port (or two-port) device is isolated,
it won't get this information from other WiFi nodes (w2sta mode).
In addition, it cannot be connected to the internet, as this would
require the port to be in WAN mode. It is also not possible to
connect a client device for configuration, since WiFi is not
configured and the LAN port is in BATMAN mode.
To enable configuration of an isolated one-port/two-port device,
this patch thus changes the default port config to CLIENT, so
the user can choose the desired configuration more easily.
For two-port, we will have one port WAN and the second port
CLIENT.
Fixes#110
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Harald Thuemmler <int@bnhof.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Fixes: #101
Signed-off-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes#83
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Christian Dresel <fff@chrisi01.de>
Just disable autoconf.
Some sysctl's are currently not available due some missing kernel
features. Maybe some day they reappear.
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Christian Dresel <fff@chrisi01.de>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Christian Dresel <fff@chrisi01.de>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Christian Dresel <fff@chrisi01.de>
The AR150 seems to have the same MAC address on eth0, eth1 and
phy0. Although it is not a ONEPORT, we can use the shifted bit
like for the ONEPORT devices to get a distinct ETHMESHMAC.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
If the mac is read from /sys/class/net/${iface}/address, some
devices (WA860RE, Picostation) will not set the fdff addresses.
This can be fixed by using the $ROUTERMAC in configurenetwork.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Previously, IPv6 addresses were constructed by reading from
the device config file in the function. To have more options,
it is better to use the address itself as parameter.
By this way we can decide what we use for getting the MAC when
calling.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This is a cosmetical patch, however it does increase the overview
a lot in my opinion.
We cannot drop the special case of the two-port devices, because
we need the current setup to enable setting port mode in the Web
UI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This is the correct firmware for the Unifi AC Mesh I have only
tested at Unifi AC Mesh and not at Unifi AC lite But my information
is, that both have the same Hardware
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since we change only the network part of uci, we only need to
commit this part and not the whole config five times.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
- Rebased
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Using wifi devices makes it possible to get mac address
without having to configure wifi networks.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Tested-By: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
- Increment package version
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
This makes use of the SWITCHDEV variable to ensure that the
correct interface is used for mac address fixing on devices,
that do not use eth0 for the switch.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Some MAC adresses were forgotten/not updated in a previous
patch. This is fixed now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
This is based on the LEDE pull request as on 2017-10-17.
Tested successfully on device (including flashing factory
image, no TFTP).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This patch achieves multiple goals:
- Align WR841 boardnames with image names
- Fix wrong name replace in sysupgrade
- Support sysupgrade of WR841 v12
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
- Rebased
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
This adds information to the switch port overview and shows
the VLAN configuration. For some routers the port order is
provided, so the physical arrangement is resembled in the
Web UI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This allows for more latitude when evaluating the addresses needed for br-mesh and ethmesh.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Tested-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ROUTERMAC is not set in the network.* file. This causes a problem
when the ULA addresses are set based on the br-mesh MAC. If we just
add the ROUTERMAC, everything should be fine.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
This puts the code for creating IPv6 addresses from MAC
address and EUI into functions, so it can be reused.
This should be particularly helpful if code is rewritten later.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Since disabling 5 GHz is complicated with KeyXchange v2, we
enable it again.
This may lead to an instable device!
This reverts commit f47e046293.
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Since there is a PKG_NAME variable, there is no need to repeat
the individual package name five times.
This makes editing and particularly copying Makefiles much
easier, as only the PKG_NAME has to be changed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This writes CLIENT/BATMAN/WAN port configurations for devices
with switches to a separate file. This file can be changed
based on the desired setup and is then preserved during
firmware upgrade. In case of a future bugfix concerning the
entries of a specific network.* file, this will still be
effective as only the port configurations reside in the
new file, while the other settings could be overwritten by
the upgrade.
For one- and two-port devices, adjustments have been made so
that their relevant settings also reside in the new file now.
This also adds a WebUI interface for setting the two-port
devices (CPE210 and CPE510).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
- Changed doc in network.mode
This only sets the switch configs if they are not set yet.
If the network.* file is edited, add FORCEPARSE=1 to apply
the changes.
Fixes#56
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WR841 v12 is using the file from v11, the new file has never
been used.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This patch adds support for the WR841N v12. For TFTP recovery, the
image name has to be wr841nv11_tp_recovery.bin (with 11, not 12)!
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Dieses Patch fügt den Support für den WR1043 v4 hinzu. Dieses Patch
baut auf den LEDE Patch auf und darf erst nach dem LEDE Patch
applied werden.
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
5Ghz AdHoc is not working with current ath10k driver.
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Michael Fritscher <michael@fritscher.net>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
cleaned up config files (moved commands to script)
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Tested-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Jan Kraus <mayosemmel@gmail.com>
- mv /etc/network.* files to package
- mv /etc/config/network to package
- also removes the bsp specific root_file_system
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Changed mode of configurenetwork to 755
Signed-off-by: Tim Niemeyer <tim@tn-x.org>