This reverts commit 3e27bff731.
Removing these busybox features breaks wireless configuration in various
confusing ways. Revert this change until further analysis.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
ci/woodpecker/push/woodpecker Pipeline was successfulDetails
Building htop with lm-sensors support currently breaks x86_64 image
building. Disable lm-sensors support for all platforms for now, because
we are currently not including lm-sensors anyway.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
A bigger squashfs block size improves compression ratio. The improved
compression ratio is necessary for the Archer C60 devices (v1 + v2)
because they include large wifi drivers.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
ci/woodpecker/push/woodpecker Pipeline was successfulDetails
The flash of some devices is too small to accomodate the additional
wolfssl library, which is included by default on OpenWrt 22.03.
In the future, the currently included mbedtls library should be replaced
with wolfssl, so WPA3, OWE and 802.11s encryption can be used.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Bump core, packages and routing.
Remove upstreamed build patches.
Remove ath10k memory hack and use the newly added ath10k-smallbuffers
variant instead, but only for devices which actually require it
(and therefore use ath10k-ct-smallbuffers by default).
Adjust for the newly introduced band option for wireless devices, which
is now emitted by OpenWrt by default.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
The Bullet M (XM) was sold with two different SoCs, AR7241 and
AR7240, which cannot be served by one DTS. This implements both
versions as done in OpenWrt.
Note that those variants may not be distinguished from the outside.
The AR7241 version appears to be the more recent and more abundant
version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Some devices were renamed since the last stable release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Flashing instructions:
The factory image needs to be uploaded via the OEM firmware GUI.
Notes:
The device is implemented as two-port in OpenWrt, i.e. it has
eth0/eth1 interfaces without switch setup. As our firmware currently
does not support that, this uses a switch setup with one port for
LAN.
Signed-off-by: Fabian Eppig <fabian@eppig.de>
[add commit message, apply alphetic sorting in bsp, remove config
changes apart from adding CONFIG_TARGET_DEVICE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch moves device support for ar71xx devices that are supported
in ath79. Building them with ath79 will be the new default.
The only devices remaining in ar71xx will be the following, as backporting
them to openwrt-19.07 is too complicated:
- cpe210-v1
- cpe510-v1
Accordingly, no tiny devices are left in ar71xx and we can drop the relevant
patches, and build ar71xx as generic again.
For the tl-wr741nd-v2, in ath79 the tplink_tl-wr741-v1 image is used.
The move from ar71xx to ath79 requires some adjustments on the way:
- The board names and image names on ath79 contain the vendor name,
where the former have it separated by a comma (tplink,cpe210-v2)
and the latter use an underscore (tplink_cpe210-v2). It is
safe to assume that this is the only difference between board and
image names.
Consequently, the ath79 devices will use their full board name also
in our firmware. A lot of renames in fff-boardname can be dropped.
The rename for fff-sysupgrade is already present in fff-upgrade.sh
While at it, fix that for the WDR4900 v1 as well.
- Due to a different switch driver, the startup of ethernet devices
is altered, which leads to eth0 and eth1 being swapped for some ath79
devices compared to ar71xx. This has been adjusted for SWITCHDEV/WANDEV
and MAC address setup.
- Since we have direct support for the AC Mesh now, use the proper
name instead of the AC Lite image. For Ubiquiti, different device
variants are now available as separate images.
- Remove left-over power-m-xw entry in cpuport file
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Tested-by: Fabian Bläse <fabian@blaese.de>
Fabian Bläse
Wolfgang Hüttenhofer
Adrian Schmutzler
Fabian Eppig