The rssileds package has never been working for our firmware, and
most probably there is no way to make it work with the current
frequent status changes of WiFi interfaces.
So, the package is just wasted space on the flash, particularly for
the "tiny" TP-Link WA850RE v1. Despite, it has a dependency on
libiwinfo, which we plan to remove as well.
Consequently, this patch removes the package for all devices. As the
package is selected per-device, we also have to remove it per-device.
The choice of devices is based on which of them includes the package
in OpenWrt 19.07.2.
The script for disabling rssileds is kept as well, as the manual
removal of the package is prone to have it overlooked for newly added
devices or when OpenWrt changes the setting for existing ones.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
The iwinfo utility is not used anywhere, so it can be removed.
This saves an additional xy KiB of space in the compressed binary,
which allows building our firmware with OpenWRT 19.07.2 for
non-LZMA 4 MiB flash devices.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Previously, the squashfs blocksize has been increased to 512 bytes,
to increase compression efficiency, because the OpenWRT default blocksize
has been only 256 bytes.
Since OpenWRT 18.06 the blocksize has been increased to 1024 bytes for
devices with a small flash. Because increased blocksize gives us additional
headroom for devices with only 4 MiB flash, our own 512 byte override is removed.
The default blocksize for the other targets in our firmware is 256, which is lower
than our current override. Therefore it is not changed in this commit.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
A wpa_supplicant is not necessary for our firmware,
because it does not connect to encrypted WiFi networks.
Therefore it is possible to use the smaller hostapd-mini
instead of the combined wpad-mini packages.
Some user might use an unsupported setup, where an encrypted
wifi is used for wan uplink. This is not possible anymore.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
The bsp .config only contain configuration, which differs from
the OpenWRT defaults. With OpenWRT 19.07, some defaults were
changed, so overriding them isn't necessary anymore.
This includes the switch from ath10k to ath10k-ct, which is now
default in OpenWRT. Our previous setup used the ct driver, but the
non-ct firmware for some devices. All devices are now reverted to
the OpenWRT default, which uses the ct variant for both the firmware
and the driver. According to some reports, the ct driver breaks
802.11s mesh for some devices, therefore these changes should be tested
before release if possible.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The qca9888-ct firmware is used as a device package for the
C60v1 and C60v2. It doesn't get built however, as it isn't selected
anywhere.
To be able to use the firmware, it is now configured to be built as a module.
Fixes: #129
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, building the firmware happens in parallel subdirectories
of "build", one for each subtarget. However, OpenWrt itself is
capable of hosting several target builds in its directory, so
there is no need for this extra separation.
This patch thus build all targets/subtargets directly in the
"build" folder.
Since most of the time during build is spent for the toolchain,
this will also significantly boost build time if more than one
target is used.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
These packages are pulled automatically by OpenWrt where needed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
We use simple-tc for traffic shaping. If those packages are
actually dependencies of other packages, they should be added
there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Looks like we do not need this package.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
In OpenWrt 18.06.2, tiny devices have increased in size so that
another packages removal is requires.
Fixes#122.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
This device is still in PR state in OpenWrt, since ar71xx target
is deprecated and thus lacking reviewers.
It worked nicely for me anyway, so I include the current state of
the PR (has not changed for months).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
With our dynamic resetting of WiFi interfaces, the rssileds
of OpenWrt do not work correctly. This disables them as a
workaround, since they otherwise create about 20 % CPU load.
Since the MACH file for all CPE210/510 is the same, no adjustment
of the OpenWrt-tiny patch is needed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
USB support is removed because of very limited flash.
This allows building for tl-mr3020 again.
USB support has no known use case for this firmware.
Most usb devices would require additional drivers anyway.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
OpenWRT changed their structure to use sysctl.d subfiles.
The default sysctl.conf is empty and kernel.panic=3 is defined
elsewhere. Thus, we do not need sysctl.conf anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
To provide data processing information for SSH access without
annoying users too much, this adds a pointer to more extensive
information to the banner displayed after login.
The referenced files then contain similar information to what
is shown in the WebUI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Tested-by: Christian Dresel <fff@chrisi01.de>
This is the correct firmware for the Unifi AC Mesh I have only
tested at Unifi AC Mesh and not at Unifi AC lite But my information
is, that both have the same Hardware
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Prepares a subtarget variable for cases where it is not 'generic'
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
- Rebased
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
This is based on the LEDE pull request as on 2017-10-17.
Tested successfully on device (including flashing factory
image, no TFTP).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
This package connects to keyxchangev2
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WR841N v12. For TFTP recovery, the
image name has to be wr841nv11_tp_recovery.bin (with 11, not 12)!
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Dieses Patch fügt den Support für den WR1043 v4 hinzu. Dieses Patch
baut auf den LEDE Patch auf und darf erst nach dem LEDE Patch
applied werden.
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
- This will fix the LEDs on LEDE
- We will lose the power heartbeat trigger on the LED
- We will lose the VPN signaling on the LEDs
While remove the default system config, the LEDE system now
configures wrong ntp service. We fix this by deleting these
entries in the fff-timeserver package.
If the file is already present on the devices, we need to upgrade it.
Therefore the 05-config-system-migration is now part of the fff-sysupgrade
package.
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
5Ghz AdHoc is not working with current ath10k driver.
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Michael Fritscher <michael@fritscher.net>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
- mv /etc/network.* files to package
- mv /etc/config/network to package
- also removes the bsp specific root_file_system
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
- mtu of 1528 is enough for no fragmentation
- also some cleanups
- interface 'bat' was never needed
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Changed mode of configurenetwork to 755
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Signed-off-by: Tobias Klaus <tk+ff@meskal.net>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
* adds openwrt patch
* adds networkconfig
power-LED is not working
Signed-off-by: Tobias Klaus <tk+ff@meskal.net>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
[rebased to master]
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
- remove httpd from .config
- remove httpd startup from rc.local
- add crawldata path creation in nodewatcher
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Tested-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Tested-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
- moves the node<-->client ra rules to package fff-uradvd
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Tested-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
also changed image comparing at sysupgrade to sha256 and added the related tool
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
also removed function board_clean from bsp files and board_postbuild from buildscript
Signed-off-by: Jan Kraus <mayosemmel@gmail.com>
suggested-by: Alexander Wunschik <freifunk@wunschik.net>
Co-Authored-by: Alexander Wunschik <freifunk@wunschik.net>
Co-Authored-by: Tobias Klaus <tk+ff@meskal.net>
Reviewed-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
This patch adds a prefix advertisment for each node. Every node get also
the IPs
* $prefix::MAC
* $prefix::link-local
* $prefix::1
::1 is duplicated so we need filtering to not forward data into the
network for ::1.
Signed-off-by: Tim Niemeyer <tim.niemeyer@mastersword.de>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com
Reviewed-by: Tobias Klaus <tk+ff@meskal.net>
Der TP-Link WA850RE ist von der Hardware baugleich mit dem WA860RE somit
wurde die Konfiguration zu größten Teilen kopiert. Der einzige
Unterschied ist der, das der Router keinen Durchgang für den Strom hat
und somit eine Steckdose blockiert.
Signed-off-by: Christian Dresel <fff@chrisi01.de>
Reviewed-by: Tim Niemeyer <tim.niemeyer@mastersword.de>
With micrond it is possible that every package has its own crontab.
Signed-off-by: Tim Niemeyer <tim.niemeyer@mastersword.de>
Reviewed-by: Steffen Pankratz <kratz00@gmx.de>
As we don't even have a DHCP server in the image.
Signed-off-by: Steffen Pankratz <kratz00@gmx.de>
Reveiwed-by: Tim Niemeyer <tim.niemeyer@mastersword.de>
- 'hidden = 1' does not make sense for ad-hoc networks, they need the
SSID to be visible for cell merging to function properly
Signed-off-by: Steffen Pankratz <kratz00@gmx.de>
Reveiwed-by: Tim Niemeyer <tim.niemeyer@mastersword.de>