The SPDX license identifier provides a standardized way for specifying
licenses that is both human- and machine-readable. It is used upstream
both in OpenWrt and the Linux kernel.
Replace licenses in our repository by those identifiers.
The full-text licenses corresponding to these identifiers are
provided in the LICENSES folder.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Fabian Bläse <fabian@blaese.de>
Instead of exposing the CPUPORT variable to the calling script
directly, wrap it into a function which can be called there.
Fixes: #52 (gitea)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Add support for the TP-Link Archer C50 v4, a low-cost mt7628-based
dual-band router.
Label MAC address is on ethernet and 2.4 GHz WiFi.
The v4 uses the same hardware as the v3 variant, but v4 includes
the newer split uboot.
ATTENTION:
Initial flashing of this device requires additional steps:
As all installation methods require an U-Boot to be integrated into the
image (and we do not ship one with the image) we are not able to create
an image in our build-process.
Download a TP-Link image from their Website and a FFF/OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
This image can be used for Web-UI and recovery, but not TFTP.
Additional instruction can be found in the OpenWrt commit
01dcd574a248 ("ramips: add support for Archer C50 v4")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
The factory image can either be flashed via the vendor WebUI or
the bootloader using nmrpflash.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch moves device support for ar71xx devices that are supported
in ath79. Building them with ath79 will be the new default.
The only devices remaining in ar71xx will be the following, as backporting
them to openwrt-19.07 is too complicated:
- cpe210-v1
- cpe510-v1
Accordingly, no tiny devices are left in ar71xx and we can drop the relevant
patches, and build ar71xx as generic again.
For the tl-wr741nd-v2, in ath79 the tplink_tl-wr741-v1 image is used.
The move from ar71xx to ath79 requires some adjustments on the way:
- The board names and image names on ath79 contain the vendor name,
where the former have it separated by a comma (tplink,cpe210-v2)
and the latter use an underscore (tplink_cpe210-v2). It is
safe to assume that this is the only difference between board and
image names.
Consequently, the ath79 devices will use their full board name also
in our firmware. A lot of renames in fff-boardname can be dropped.
The rename for fff-sysupgrade is already present in fff-upgrade.sh
While at it, fix that for the WDR4900 v1 as well.
- Due to a different switch driver, the startup of ethernet devices
is altered, which leads to eth0 and eth1 being swapped for some ath79
devices compared to ar71xx. This has been adjusted for SWITCHDEV/WANDEV
and MAC address setup.
- Since we have direct support for the AC Mesh now, use the proper
name instead of the AC Lite image. For Ubiquiti, different device
variants are now available as separate images.
- Remove left-over power-m-xw entry in cpuport file
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Tested-by: Fabian Bläse <fabian@blaese.de>
When adding support for the TP-Link Archer C50 v3 and TL-WR841N v13,
their CPU port provided for layer-3 setup has not been set correctly.
Do it now.
Fixes: d165915178 ("ramips/mt76x8: Add support for TP-Link Archer C50 v3")
Fixes: 9343153547 ("ramips/mt76x8: Add support for TP-Link TL-WR841N v13")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
This provides the CPUPORT which is needed for the gateway firmware.
The script is supposed to be sourced.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Adrian Schmutzler
Fabian Bläse