The name br-mesh is actually quite misleading, since the bridge
actually includes the "client" interfaces. In order to make this
obvious, and to prevent confusion with the properly named wXmesh
interfaces, rename them to br-client.
Note that br-mesh is also particularly disturbing for the layer 3
firmware without batman-adv.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Fabian Bläse <fabian@blaese.de>
Acked-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
For historic reasons, the wan interface is set to eth1 as default
value. When updating the config for one-port devices in
configurenetwork, the same value is put there again if the mode
is switched to something != WAN, instead of just removing the
value.
While ifname actually is a mandatory value, this has been handled
inconsistently in the past, where ethmesh ifname was deleted, and
wan ifname was just changed back to eth1, when assigning the
actually relevant eth0 to a different task.
This concept was set up with a one-port device in mind, i.e. a
device where there is no eth1. However, this very setup routine
got applied to the Nanostation M as well (which is treated as
as one-port), where we suddenly have two interfaces and the eth1
exists.
So, while the user assumes it's unconfigured, the second port
actually becomes set up as WAN if the first one is != WAN.
If connected to a second device with CLIENT (=default) to provide
PoE there, this will create a loop.
So, finally, in order to somehow fix this mess, this patch just
changes the hardcoded "eth1" to "eth2". While this is no proper
fix, it perpetuates the original idea of keeping wan set to
something, but nothing which actually exists. However, there are
no sideeffects and we keep this minimal-invasive.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Until now, IPv6 connectivity was only ensured by some custom sysctls.
OpenWrt has a proper way of enabling IPv6 client (SLAAC, as well as DHCPv6)
for an interface. Switching to OpenWrt's way of configuring client addresses
for an interface might also make configuration more reliable, as the appropriate
sysctls are now set by netifd. Especially OnePort and TwoPort devices will
benefit from this change, as IPv6 auto configuration does not have to be manually
enabled and disabled for a physical interface, but rather is set as an option for
our logical wan interface.
At the same time this change enables DHCPv6 client support for WAN.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This migrates to the new configuration architecture introduced
and required in
54af5a209e
This is a side-effect of the switch to openwrt-19.07.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fabian@blaese.de: Rebase onto fff firmware master]
Signed-off-by: Fabian Bläse <fabian@blaese.de>
This interface was using 1500 anyway and setting ethernet to
MTU > 1500 might not be a good idea.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Langammer <rlanghammer@web.de>
- mv /etc/network.* files to package
- mv /etc/config/network to package
- also removes the bsp specific root_file_system
Signed-off-by: Tim Niemeyer <tim@tn-x.org>
Reviewed-by: Jan Kraus <mayosemmel@gmail.com>
Adrian Schmutzler
Fabian Bläse
Tim Niemeyer