Memory consumption has increased enough with OpenWrt 21.02, that
devices with 32 MB memory do not work reliably anymore.
It might be possible to work around the 4 MB flash limitation, but
reducing memory consumption is quite a bit harder. It is very likely
that this is only possible with a signifcant reduction of feature.
As we do not support any devices that have enough memory but only 4 MB
of flash, drop support for devices with less than 8/64 MB alltogether.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed by: Robert Langhammer <rlanghammer@web.de>
This migrates the support for the TP-Link CPE210 v1 and CPE510 v1
so they are recognized by the new two-port setup code.
Assignment of ports should be consistent to the ar71xx implementation,
i.e. primary port (PoE in) assigned to WAN and secondary port (PoE out)
assigned to CLIENT by default.
Note that this is the exact opposite of the default configuration of
what OpenWrt does (but both have been consistent in behavior).
Since they work again, also re-enable image transfer.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
The Bullet M (XM) was sold with two different SoCs, AR7241 and
AR7240, which cannot be served by one DTS. This implements both
versions as done in OpenWrt.
Note that those variants may not be distinguished from the outside.
The AR7241 version appears to be the more recent and more abundant
version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
In the latest release, OpenWrt provides the label MAC address for
many devices. All of our devices should be covered.
In can be retrieved by the function
get_mac_label
from /lib/functions/system.sh
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Some devices were renamed since the last stable release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
In '/etc/network.ubnt,unifiac-mesh', we include a file that does
not exist on ath79 anymore. This causes the script execution to
abort and will have configurenetwork not run at all, making the
device quite inaccessible.
Remove the include as it never had any use anyway. Remove another
unused include as well, and add the proper dependency instead.
This fix was first proposed more than 2.5 years ago.
Fixes: #130 (gitea)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Migration from ar71xx to ath79 included changes to the ethernet/switch
driver for the target. This introduced a peculiar issue where
eth0 and eth1 are swapped for several devices. Most of the relevant
cases were already covered in 1cf4d762ff ("treewide: move devices
from ar71xx to ath79").
This switch also affects the Nanostation M, where the PoE-in port
is now eth1 und the PoE-out port is eth0. However, no action was
taken in the referenced patch, as nobody was aware of it then.
Since the Nanostation M is a two-port device, which we cannot
implement properly so far, it was implemented as a one-port with
the "primary" PoE-in port so far. This was broken by the ath79
introduction and is now fixed in this patch by using the one-port
setup on eth1. That way, the PoE-in port can now be switched by
ETHMODE as usual again.
Note that custom scripts, e.g. to set up the second port, need to
be adjusted manually, as that one is eth0 now.
Fixes: 1cf4d762ff ("treewide: move devices from ar71xx to ath79")
Fixes: #109 (gitea)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Tested-by: Fabian Bläse <fabian@blaese.de>
So far, we define PORTORDER individually in each network.* file.
This creates a lot of duplications, and makes the code to parse those
values very ugly (and it's only used outside of configurenetwork
anyway).
Therefore, move the assignment to a library file, and wrap it into
a function for tidyness. This gives us more overview and nicer
implementation of the retrieval.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Christian Dresel <freifunk@dresel.systems>
Reviewed-by: Robert Langhammer <rlanghammer@web.de>
Flashing instructions:
The factory image needs to be uploaded via the OEM firmware GUI.
Notes:
The device is implemented as two-port in OpenWrt, i.e. it has
eth0/eth1 interfaces without switch setup. As our firmware currently
does not support that, this uses a switch setup with one port for
LAN.
Signed-off-by: Fabian Eppig <fabian@eppig.de>
[add commit message, apply alphetic sorting in bsp, remove config
changes apart from adding CONFIG_TARGET_DEVICE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
OpenWrt only builds and installs a packet for each architecture.
If a package is already fully built and installed for a architecture,
it is not rebuilt.
Because we have two different BSPs building two different targets (BOARDs)
using the same architecture (ath79 and ar71xx, mips), the fff-network package
is not reinstalled when switching between those.
However, we have defined an install step, which copies the necessary network
files seperated by board. But because the package is not rebuilt when switching
targets, the wrong network files might be present in the package.
To resolve this issue, the network files are now seperated by ARCH instead of
the target (i.e. the BOARD variable).
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Robert Langhammer <rlanghammer@web.de>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fabian Bläse
Adrian Schmutzler
Fabian Eppig