Memory consumption has increased enough with OpenWrt 21.02, that
devices with 32 MB memory do not work reliably anymore.
It might be possible to work around the 4 MB flash limitation, but
reducing memory consumption is quite a bit harder. It is very likely
that this is only possible with a signifcant reduction of feature.
As we do not support any devices that have enough memory but only 4 MB
of flash, drop support for devices with less than 8/64 MB alltogether.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed by: Robert Langhammer <rlanghammer@web.de>
This migrates the support for the TP-Link CPE210 v1 and CPE510 v1
so they are recognized by the new two-port setup code.
Assignment of ports should be consistent to the ar71xx implementation,
i.e. primary port (PoE in) assigned to WAN and secondary port (PoE out)
assigned to CLIENT by default.
Note that this is the exact opposite of the default configuration of
what OpenWrt does (but both have been consistent in behavior).
Since they work again, also re-enable image transfer.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
OpenWrt 21.02 only uses ath79, ar71xx has been dropped. However,
in ath79 the TP-Link CPE210 v1 and CPE510 v1 are implemented as
two-port devices. We currently do not support that in our firmware.
Thus, disable both devices by commenting out their image selectors.
Note that this will still build them, and only prevent having the
images in our dedicated folder.
If support is reestablished, this patch simply needs to be
reverted.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Bullet M (XM) was sold with two different SoCs, AR7241 and
AR7240, which cannot be served by one DTS. This implements both
versions as done in OpenWrt.
Note that those variants may not be distinguished from the outside.
The AR7241 version appears to be the more recent and more abundant
version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Some devices were renamed since the last stable release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Flashing instructions:
The factory image needs to be uploaded via the OEM firmware GUI.
Notes:
The device is implemented as two-port in OpenWrt, i.e. it has
eth0/eth1 interfaces without switch setup. As our firmware currently
does not support that, this uses a switch setup with one port for
LAN.
Signed-off-by: Fabian Eppig <fabian@eppig.de>
[add commit message, apply alphetic sorting in bsp, remove config
changes apart from adding CONFIG_TARGET_DEVICE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch moves device support for ar71xx devices that are supported
in ath79. Building them with ath79 will be the new default.
The only devices remaining in ar71xx will be the following, as backporting
them to openwrt-19.07 is too complicated:
- cpe210-v1
- cpe510-v1
Accordingly, no tiny devices are left in ar71xx and we can drop the relevant
patches, and build ar71xx as generic again.
For the tl-wr741nd-v2, in ath79 the tplink_tl-wr741-v1 image is used.
The move from ar71xx to ath79 requires some adjustments on the way:
- The board names and image names on ath79 contain the vendor name,
where the former have it separated by a comma (tplink,cpe210-v2)
and the latter use an underscore (tplink_cpe210-v2). It is
safe to assume that this is the only difference between board and
image names.
Consequently, the ath79 devices will use their full board name also
in our firmware. A lot of renames in fff-boardname can be dropped.
The rename for fff-sysupgrade is already present in fff-upgrade.sh
While at it, fix that for the WDR4900 v1 as well.
- Due to a different switch driver, the startup of ethernet devices
is altered, which leads to eth0 and eth1 being swapped for some ath79
devices compared to ar71xx. This has been adjusted for SWITCHDEV/WANDEV
and MAC address setup.
- Since we have direct support for the AC Mesh now, use the proper
name instead of the AC Lite image. For Ubiquiti, different device
variants are now available as separate images.
- Remove left-over power-m-xw entry in cpuport file
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Fabian Bläse <fabian@blaese.de>
Tested-by: Fabian Bläse <fabian@blaese.de>
Fabian Bläse
Adrian Schmutzler
Fabian Eppig